In this study, the fractal dimensions of failure surfaces of vinyl ester based nanocomposites are estimated using two classical methods, Vertical Section Method (VSM) and Slit Island Method (SIM), based on the processing of 3D digital microscopic images. Self-affine fractal geometry has been observed in the experimentally obtained failure surfaces of graphite platelet reinforced nanocomposites subjected to quasi-static uniaxial tensile and low velocity punch-shear loading. Fracture energy and fracture toughness are estimated analytically from the surface fractal dimensionality. Sensitivity studies show an exponential dependency of fracture energy and fracture toughness on the fractal dimensionality. Contribution of fracture energy to the total energy absorption of these nanoparticle reinforced composites is demonstrated. For the graphite platelet reinforced nanocomposites investigated, surface fractal analysis has depicted the probable ductile or brittle fracture propagation mechanism, depending upon the rate of loading.

The current work focuses on evaluation of the effective elastic properties of cementitious materials through a voxel based finite element analysis (FEA) approach. Voxels are generated for a heterogeneous cementitious material (type-I cement) consisting of typical volume fractions of various constituent phases from digital microstructures. The microstructure is modeled as a microscale representative volume element (RVE) in ABAQUS V R to generate cubes several tens of microns in dimension and subjected to various prescribed deformation modes to generate the effective elastic tensor of the material. The RVE-calculated elastic properties such as moduli and Poisson's ratio are validated through an asymptotic expansion homogenization (AEH) and compared with rule of mixtures. Both periodic (PBC) and kinematic boundary conditions (KBC) are investigated to determine if the elastic properties are invariant due to boundary conditions. In addition, the method of "Windowing" was used to assess the randomness of the constituents and to validate how the isotropic elastic properties were determined. The average elastic properties obtained from the displacement based FEA of various locally anisotropic microsize cubes extracted from an RVE of size 100 Â 100 Â 100 lm showed that the overall RVE response was fully isotropic. The effects of domain size, degree of hydration (DOH), kinematic and periodic boundary conditions, domain sampling techniques, local anisotropy, particle size distribution (PSD), and random microstructure on elastic properties are studied.

No abstract

This study explores the mechanical properties of an E-glass fabric composite reinforced with anchored multi-walled carbon nanotubes (CNTs). The CNTs were grown on the E-glass fabric using a floating catalyst chemical vapor deposition procedure. The E-glass fabric with attached CNTs was then incorporated into resin based composites and compared to similar composites without CNTs. Long and short beam bending tests, uniaxial compression measurements for energy dissipation, high strain-rate Split-Hopkinson pressure bar measurements, and ballistic performance (V50) tests were performed to characterize the mechanical properties of the CNT composites. The CNT composites showed a reduction in interlaminar shear strength by 25.9 %. They also showed an increase in the specific energy absorption by 106 % at high strain rates and an increase in energy density dissipation by 64.3 % after 5 cycles at quasi-static strain rates. In ballistic V50 tests, the CNT based composites showed a higher V50 value by 11.1 %. Due to their reduced weight and energy dissipation properties, the direct growth of CNTs on E-glass fabrics incorporated into composites have potential defense applications such as blast protection.

The dynamic mechanical behavior and high-strain rate response characteristics of a functionally graded material (FGM) system consisting of vertically aligned carbon nanotube ensembles grown on silicon wafer substrate (VACNT-Si) are presented. Flexural rigidity (storage modulus) and loss factor (damping) were measured with a dynamic mechanical analyzer in an oscillatory three-point bending mode. It was found that the functionally graded VACNT-Si exhibited significantly higher damping without sacrificing flexural rigidity. A Split-Hopkinson pressure bar (SHPB) was used for determining the system response under high-strain rate compressive loading. Combination of a soft and flexible VACNT forest layer over the hard silicon substrate presented novel challenges for SHPB testing. It was observed that VACNT-Si specimens showed a large increase in the specific energy absorption over a pure Si wafer.