Diesel engines use diffusion-controlled combustion of a high-reactivity fuel and offer high efficiencies because they combine lean combustion with a high compression ratio. For low-reactivity fuels such as gasoline or natural gas, premixed combustion is used, which leads to lower efficiency levels as usually stoichiometric combustion is combined with lower compression ratios. Trying to apply diesel-like process parameters to low-reactivity fuels inevitably leads to problems with classical spark ignition systems as they are not able to establish robust flame propagation for such hard-to-ignite conditions. One possibility to enable fast combustion for diluted mixtures at high pressure levels is to establish ignition in a prechamber and ignite the charge of the main combustion chamber using the turbulent jets exiting the prechamber. In this study, the experimental results of a prechamber-equipped four-cylinder natural gas engine with 2 L displacement are discussed in detail. In the majority of the engine map, auxiliary fueling is used in the prechamber and a global air–fuel equivalence ratio λ is set to 1.7. At full load, a λ of 1.5 is applied without auxiliary prechamber fueling. The experiments show that such a setup is able to achieve brake efficiency levels of above 45% while maintaining peak brake mean effective pressure levels above 20 bar. At high load conditions, cylinder pressure levels at ignition timing achieve more than 80 bar and cylinder peak pressures of around 180 bars occur. The technology proved to enable robust and very fast combustion at comparably low NOx levels. A remaining challenge for the on-road use of such a technology is the reduction of the methane emissions at lean conditions.

Today’s passenger car CNG engines are based on petrol engines which typically have restrictions preventing the exploitation of the full potential of methane based fuels, especially if they have to be operated also on petrol as a second fuel. Additionally, the use of three-way-catalysis limits the engine operation to λ = 1. Here, we present the efficiency potential and the raw emission characteristics for a dedicated four cylinder passenger car CNG engine without sticking to the usual combustion peak pressure and λ limitations. Lean com-bustion reduces the knocking tendency but, because of the higher pressure levels, increases the ignition energy demand. Therefore, dif-ferent ignition systems (spark plug, prechamber, Diesel pilot) have been used.

No abstract

Analysis of non-legislated engine-emission components, with different exhaust-gas after-treatment techniques, is an important air quality objective. This paper reports the results for various nitrogen oxides, ammonia and differentiated hydrocarbons emitted at part load from a small 4-S SI-engine. It was operated with gasoline, with CNG *) and with two different three-way catalytic converters. CNG produces less HC and less aromatics. But the HC conversion rate is insufficient. This is due to the lower exhaust gas temperatures, at part load with CNG, and due to the higher stability of light HCs. CNG affects the λ-regulation window, of the investigated system, such that the NO x conversion rate is lowered. In the rich domain of the λ-regulation window, the NO & NO x emissions after catalyst were lowest, while the NH 3 formation was most intense, and vice versa. The catalyst type: precious metal, and its content, influences the conversion rates and emissions of the investigated components during light-off.

Natural gas is well-suited as a fuel in the transport sector. Due to its excellent combustion characteristics, engines operating with compressed natural gas (CNG) reach high efficiency, especially if operated at lean conditions. However, CNG engine research mainly focusses on stoichiometric conditions in order to use a three-way catalytic converter for the exhaust gas after treatment system. With the objective to explore the potential of CNG engines operated at lean conditions, a turbo-charged CNG engine with high com-pression ratio is developed and optimized for lean operation. In order to increase the ignition energy, the CNG engine is equipped with scavenged pre-chambers. A specific control structure is developed, which allows to operate the engine at a pre-defined (lean) air-to-fuel ratio. Further functionalities such as the combustion placement control and algorithms to estimate the conditions inside of the pre-chamber are implemented. The first part of this paper describes this engine control structure, which is specifically developed for the lean-burn CNG engine. In the second part, the effects of pre-chamber scavenging on engine performance criteria such as the combustion stability, engine efficiency or engine emissions are analyzed. With the objective to use pre-chamber scavenging to improve engine performance, a scavenging feed-back control strategy is proposed. In order to control the ignition delay, this strategy adapts the amount of CNG injected into the pre-chamber with a linear controller or an extremum seeking algorithm depending on the air-to-fuel ratio of the main chamber.