We present a novel method for measuring the fluctuating basal normal and shear stresses of debris flows by using along-channel seismic recordings. Our method couples a simple parameterization of a debris flow as a seismic source with direct measurements of seismic path effects using empirical Green's functions generated with a force hammer. We test this method using two large-scale (8 and 10 m 3) experimental flows at the U.S. Geological Survey debris-flow flume that were recorded by dozens of three-component seismic sensors. The seismically derived basal stress fluctuations compare well in amplitude and timing to independent force plate measurements within the valid frequency range (15-50 Hz). We show that although the high-frequency seismic signals provide band-limited forcing information, there are systematic relations between the fluctuating stresses and independently measured flow properties, especially mean basal shear stress and flow thickness. However, none of the relationships are simple, and since the flow properties also correlate with one another, we cannot isolate a single factor that relates in a simple way to the fluctuating forces. Nevertheless, our observations, most notably the gradually declining ratio of fluctuating to mean basal stresses during flow passage and the distinctive behavior of the coarse, unsaturated flow front, imply that flow style may be a primary control on the conversion of translational to vibrational kinetic energy. This conversion ultimately controls the radiation of high-frequency seismic waves. Thus, flow style may provide the key to revealing the nature of the relationship between fluctuating forces and other flow properties. Few monitoring sites rely solely on seismic methods, in part due to the lack of clear quantitative links between seismic signals and flow characteristics. By necessity, most sites combine seismic sensors with nonseismic monitoring methods such as tripwires, pendulums, cameras, flow depth sensors, and manned watch stations (e.g.,

Debris flows evolve in both time and space in complex ways, commonly starting as coherent failures but then quickly developing structures such as roll waves and surges. These processes are readily observed but difficult to study or quantify because of the speed at which they evolve. Many methods for studying debris flows consist of point measurements (e.g., flow height or basal stresses), which are inherently limited in spatial coverage and cannot fully characterize the spatiotemporal evolution of a flow. In this study, we use terrestrial lidar to measure debris-flow profiles at high sampling rates to examine debris-flow movement with high temporal and spatial precision and accuracy. We acquired measurements during gate-release experiments at the U.S. Geological Survey debris-flow flume, a unique experimental facility where debris flows can be artificially generated at a large scale. A lidar scanner was used to record repeat topographic profiles of the moving debris flows along the length of the flume with a narrow swath width (∼1 mm) at a rate of 60 Hz. The high-resolution lidar profiles enabled us to quantify flow front velocity of the debris flows and provided an unprecedented record of the development and evolution of the flow structure with a sub-second time resolution. The findings of this study demonstrate how to obtain quantitative measurements of debris-flow movement. In addition, the data help us to quantitatively define the development of a saltating debris-flow front and roll waves behind the debris-flow front. Such measurements may help constrain future modeling efforts.

Noncontact measurements of spatially varied ground surface deformation during landslide motion can provide important constraints on landslide mechanics. Here, we present and test a new method for extracting measurements of rapid landslide surface displacement and velocity (accelerations of approximately 1 m/s2) using sequences of stereo images obtained from a pair of inexpensive, stationary 4K video cameras with nominal frame rates of 29.97 Hz. The method combines elements of Structure from Motion with those of optical flow to extract data on 3‐D evolution of the ground surface during slope failure. We apply the method to an experiment at the U.S. Geological Survey debris‐flow flume in which a high‐speed, liquefying landslide was triggered by gradually adding water to a 6‐m3 prism of loosely packed sediment on a 31° slope. Strip‐scanning lidar measurements made during the experiment corroborate our video‐based measurements, but the latter encompassed the entire landslide surface and were much lower in cost. Our video‐based measurements enabled computation of depth‐integrated landslide dilation/contraction rates. The range of computed rates was within the ranges inferred from independent measurements of evolving pore water pressures and reasonable estimates of the hydraulic permeability of the sediment. Dilation and contraction rates play a crucial role in landslide mechanics. The dilation and contraction we observe contradict the incompressible flow assumption used in many studies that have employed noncontact methods to infer landslide properties.