This paper presents the results of research on the granulation process of leather industry waste, i.e., tanning shavings. It is economically justified to granulate this waste together with mineral additives that are useful in the processes of their further processing. Unfortunately, the granulation of raw, unsorted shavings does not obtain desired results due to their unusual properties. In this study, the possibilities of agglomeration of this waste were examined by a new method consisting of the production and then the granulation of wet pulp. During granulation, no additional binding liquid is added to the granulated bed. As part of this work, the specific surface of granulated shavings, the granulometric composition of the obtained agglomerates, and their strength parameters were determined. The use of a vibrating disc granulator, the addition of a water glass solution (in the pulp), dolomite, and gypsum made it possible to obtain durable, mechanically stable granules.

a sylwia.pasieczna@poczta.umcs.lublin.pl This article describes the application of IR spectroscopic methods in the study of the composition of finished cosmetic products. Four spectroscopic techniques: TS (transmission spectroscopy), PAS (photoacoustic spectroscopy), ATR (attenuated total reflectance) and DRS (diffuse reflectance spectroscopy) were used for this purpose. Tested cosmetic products were of different consistency and application. The choice of spectroscopic techniques was dictated by the physical state and consistency of the sample.

Carbonation lime mud is a by-product formed during the production of sugar in the process of raw beetroot juice purification. On average, during one campaign, over 12,000 tons of carbonation lime mud is obtained in the operation of one sugar production plant. It is stored in prisms, which negatively affects the environment. The chemical properties of carbonation lime mud allow using it as a soil improver. This article presents the results of research into the development of carbonation lime mud disposal technology and its management. The chemical composition and physical properties of waste were determined. It has been proposed to use carbonation lime mud as the basic raw material in the production of mineral–organic fertilizers. Tests were conducted in a disc granulator. The granulated material was wetted with water and aqueous solution of molasses. Carbonation lime mud is a material that is easily subjected to the granulation process, using any wetting liquid. The beds wetted with 33% and 66% solutions of molasses are characterized by a greater homogeneity and smaller size of the obtained product. During experiments in which wetting with water was applied, the product obtained after drying demonstrated low resistance to compression; granules wetted with 33% aqueous solution of molasses demonstrated resistance to compression below 10 N; and granules wetted with 66% aqueous solution of molasses demonstrated resistance to compression above 10 N.

The application of the Discrete Element Method (DEM) allows simulating the movement of a particle of any shape in a conveyor. The DEM method uses the assumptions of the Lagrange calculation model, in which each particle in the domain is tracked individually. It makes it possible to conduct a thorough examination of the behavior of the entire bulk material bed consisting of a set of elements with characteristic physicochemical properties. Therefore, the deposit is not considered according to averages and constants, e.g., strength values, but as a set of elements that can be described individually. The article presents the results of a simulation, with the use of the Discrete Elements Method (DEM), of the process of soft fruit transport in the food industry. The results of the research and exemplary simulations of blueberry fruit transport are presented. The influence of the type of a transport device on the values of normal and tangential forces occurring between the blueberry fruit and structural elements of the transport device, as well as the interaction between the fruits, were modeled. In addition, based on the amount of energy absorbed by each fruit due to collisions, the analysis of the energy spectrum of collisions of particles was carried out to determine the likelihood of damage to the fruit in transport and to identify the phenomena that favor it.

The paper presents the results of studies on quartzite milling in a ball mill. The milling was conducted in a batch system, for diversified compositions of balls. The milling product was subjected to granulometrical, morphological and strength analyses. On the basis of the developed Reid's theory and using the Austin-Gardner equation, a form of the function circumscribing the specific rate of comminution of selected size fractions was determined. The values of the breakage rate function b i,j for the mill's apparatus conditions were determined. The impact was investigated for a variable number of grinding media contact points on the values of specific rate S and the values of the breakage rate function b i,j . Furthermore, the values of coefficients occurring in the equations circumscribing the specific rate of milling S and breakage parameter b i,j were determined.