MIL-53(Al)-graphene oxide (GO) nanocomposites of different GO to MIL-53(Al) mass ratios (1% to 25% GO) were synthesized and tested for removal of arsenite (As(III)), which is a well-known groundwater contaminant. The properties of MIL-53(Al)-GO nanocomposites were characterized using X-ray Diffraction (XRD), Fourier Transform Infrared (FT-IR) Spectroscopy, Brunauer-Emmett-Teller (BET) surface area measurements, and Scanning Electron Microscopy (SEM). Batch experiments were performed on MIL-53(Al)-GO nanocomposites for As(III) adsorption in aqueous solutions to investigate adsorption kinetics and isotherm behavior under varying environmental conditions. The effects of solution pH (2 to 11), initial As(III) concentrations (10–110 mg/L), adsorbent dosage (0.2–3.0 g/L), and temperature (298–318 K) on As(III) adsorption were investigated. MIL-53(Al)-GO nanocomposites showed higher adsorption of As(III) than pristine MIL-53(Al) and GO individually. As (III) removal was optimized at a ratio of 3% GO in the MIL-53(Al)-GO nanocomposite, with an adsorption capacity of 65 mg/g. The adsorption kinetics and isotherms followed pseudo-second-order and Langmuir isotherm models, respectively. Overall, these results suggest that MIL-53(Al)-GO nanocomposite holds a significant promise for use in the remediation of As (III) from groundwater and other aqueous solutions.

No abstract

Magnetically responsive, mechanically stable and highly flexible iron (III) oxide-polyvinylidene fluoride (Fe3O4-PVDF) piezoelectric composite fiber mats were fabricated via one step electrospinning method for magnetic sensing at cryogenic temperature. The properties of Fe3O4-PVDF composite fiber mats were characterized using scanning electron microscopy (SEM), differential scanning calorimetry (DSC), X-ray diffraction (XRD), Fourier transform infrared (FT-IR) spectroscopy, d33 and magnetization test. The fiber diameter decreased as the concentration of Fe3O4 increased. The DSC results suggested a decrease in the crystallinity of the composite fiber mats after adding Fe3O4, and the XRD curves identified that the decrease in crystallinity took place in the β crystalline phases of the fibers. FT-IR results further confirmed the reduction of β phases of the composite fiber mats which dropped the piezoelectric response of the fiber mats by 38% for 5% Fe3O4-PVDF than PVDF fiber but still 400% higher than PVDF pellets. The magnetization test advocated a superparamagnetic state of the fiber at room temperature but a ferromagnetic behavior at a lower temperature. The coercivity values of the mats suggested a homogeneous dispersion of the Fe3O4 nanoparticles into the PVDF matrix. Young’s modulus (E) of the fibers remained the same before and after the magnetization test, indicating the mechanical stability of the fiber in the range of 5 K to 300 K. Its mechanical stability, superparamagnetic behavior at room temperature and ferromagnetic at low temperature could open up its application in spintronic devices at cryogenic temperature and cryogenic power electronic devices.

Corrosion in underground and submerged steel pipes is a global problem. Coatings serve as an impermeable barrier or a sacrificial element to the transport of corrosive fluids. When this barrier fails, corrosion in the metal initiates. There is a critical need for sensors at the metal/coating interface as an early alert system. Current options utilize metal sensors, leading to accelerating corrosion. In this paper, a non-conductive sensor textile as a viable solution was investigated. For this purpose, non-woven Zinc (II) Oxide-Polyvinylidene Fluoride (ZnO-PVDF) nanocomposite fiber textiles were prepared in a range of weight fractions (1%, 3%, and 5% ZnO) and placed at the coating/steel interface. The properties of ZnO-PVDF nanocomposite meshes were characterized using scanning electron microscopy (SEM), X-ray diffraction (XRD), Fourier transform infrared (FTIR) and d33 meter. Electrochemical impedance spectroscopy (EIS) testing was performed during the immersion of the coated samples to validate the effectiveness of the sensor textile. The results offer a new option for sub-surface corrosion sensing using low cost, easily fabricated sensor textiles.

Submerged steel pipes are susceptible to corrosion due to long exposure under harsh corrosive conditions. Here, we investigated the reliability and effectiveness of nonwoven zinc(II) oxide-polyvinylidene fluoride (ZnO-PVDF) nanocomposite fiber textiles as an embedded corrosion sensor. An accelerated thermal cyclic method paired to electrochemical impedance spectroscopy (EIS) was used for this purpose. Sensor accuracy and reliability were determined using the textile and instrument as reference electrodes. The results showed that the coating and the sensor improved the corrosion resistance when ZnO was added to the sensor textile and introduced into the coating. As the coating’s glass transition was approached, the corrosion performance of the coating degraded and the sensor accuracy decreased. The results suggested that the flexible sensor is reliable at both monitoring the corrosion and acting as a corrosion barrier.