No abstract

The dynamic surface tension and equilibrium adsorption behavior of DLPC dispersions in phosphate buffer saline at 37 and 25 degrees C was studied with tensiometry, infrared reflection--absorption spectroscopy (IRRAS), and ellipsometry. The results are compared with those in water (Pinazo et al. Langmuir 2002, 18, 8888). Even though the pH and salinity have no apparent effect on the equilibrium surface tension and the surface pressure--area isotherm, they affect the dynamic surface tension by decreasing the adsorption rate and increasing the dynamic tension minima at a pulsating area of 20 or 80 cycles per minute. Moreover, IRRAS and ellipsometry results show that the adsorbed layers and the spread monolayers have larger area per molecule, or looser packing, in buffer than in water. A new hypothesis is proposed to elucidate the effect of pH/salinity on this zwitterionic surfactant: there is some specific interaction or binding between the ions from the buffer saline with the polar headgroups of DLPC. This interaction induces stronger intermolecular repulsions of the surfactant layer in buffer than that in water, despite the expected electrostatic screening effect, and causes higher dynamic surface tensions. The results have implications in designing lung surfactant replacement formulations.

No abstract

Fibrinogen (FB) and other serum proteins leak into the aqueous alveolar lining layer due to lung injuries. The adsorption of these serum proteins at the air/aqueous interface can produce higher surface tensions than the pulmonary lipids, and acute respiratory distress syndrome (ARDS) can ensue. By having a molecular adsorption mechanism, as compared to a particulate adsorption mechanism of other longer chain lipids, dilauroylphosphatidylcholine (DLPC) lipid can expel FB from the air/aqueous interface at 25 degrees C, in water or in phosphate-buffered saline, as proven by tensiometry (also at 37 degrees C), ellipsometry, and infrared reflection-absorption spectroscopy. Moreover, before FB is displaced by DLPC at the interface, there is a substantial initial enhancement in the FB adsorption, consistent with some interaction or binding of DLPC with FB to produce a more hydrophobic protein surface. After the FB molecules have been displaced by DLPC, or when DLPC has already adsorbed at the interface, FB molecules are less favored to adsorb near the DLPC monolayer with the lecithin headgroups facing toward them. The results have implications for possible uses of DLPC lipid in potential lung surfactant formulations in treating patients with ARDS.

A new method of making physically self-assembled monolayers (PSAMs) on hydrophilic solid surfaces is presented. This method uses a mixture of a nonpolar solvent, such as hexane, and a strong polar solvent, such as ethanol, to dissolve the lipids. The deposition of two lecithin lipids, dipalmitoylphosphatidylcholine (DPPC) and dilauroylphosphatidylcholine (DLPC), has been studied. These lipids physically self-assemble, or adsorb, onto hydrophilic silicon oxide/silicon surfaces when such surfaces are in contact with the lipid solution. The adsorbed layers were probed with ex-situ attenuated total reflection infrared (ATR-IR) spectroscopy, ellipsometry, contact angle measurements, and atomic force microscopy (AFM). The thicknesses of the adsorbed monolayers are about 2.8 +/- 0.2 nm for DPPC and 2.0 +/- 0.2 nm for DLPC, as determined by ellipsometry and AFM. Smooth, uniform monolayers of controlled surface density are formed. The surface density of adsorbed layers is comparable to those of close-packed lipid monolayers, as calculated from the ellipsometry and ATR-IR results. Producing controlled-thickness monolayers has applications in boundary lubrication, biomaterials, sensor technologies, and electronics. The method can be used for depositing many biological surfactants or lipids without the need to modify these surfactants chemically to form chemical bonds with the surfaces, as required by the usual chemical SAMs. Moreover, the new method has several advantages compared to the Langmuir-Blodgett (LB) method.