On the page 117407-3, left column, the text in the last paragraph should be written as follows. ''Such a small L m value means that the respective clusters are elongated along the electric field vector of the incident light, like the interface indium inclusions. In this case, the depolarization is small, and the resonance energy is the lowest among those possible [16]. This type of clusters determines the effective absorption edge in InN. The resonances of the clusters with L m 0:33 are higher in energy than the absorption edge in InN, so the prolate intercolumn inclusions do not affect the effective band edge.'' This correction affects the speculation concerning the type of the In clusters involved, but changes none of our main results.We thank T.

We report on the thorough investigation of light emitting diodes (LEDs) made of core-shell nanorods (NRs) with InGaN/GaN quantum wells (QWs) in the outer shell, which are grown on patterned substrates by metal-organic vapor phase epitaxy. The multi-bands emission of the LEDs covers nearly the whole visible region, including UV, blue, green, and orange ranges. The intensity of each emission is strongly dependent on the current density, however the LEDs demonstrate a rather low color saturation. Based on transmission electron microscopy data and comparing them with electroluminescence and photoluminescence spectra measured at different excitation powers and temperatures, we could identify the spatial origination of each of the emission bands. We show that their wavelengths and intensities are governed by different thicknesses of the QWs grown on different crystal facets of the NRs as well as corresponding polarization-induced electric fields. Also the InGaN incorporation strongly varies along the NRs, increasing at their tips and corners, which provides the red shift of emission. With increasing the current, the different QW regions are activated successively from the NR tips to the side-walls, resulting in different LED colors. Our findings can be used as a guideline to design effectively emitting multi-color NR-LEDs.

which are environmentally friendly and enable portability and high efficiency. Up to date, great progress has been made on the UVC light-emitting diodes (LEDs) by using active regions of AlGaN multiple quantum wells (MQWs) .[8-14] However, the optical output power of current UVC LEDs drops significantly as the light emission wavelength gets shorter. Those LEDs suffer from poor hole injection efficiency in high-Al-content p-type AlGaN, low internal quantum efficiency (IQE) caused by large-lattice-mismatch heteroepitaxy, and strong quantum-confined Stark effect (QCSE), as well as the absorption by the nontransparent GaN contact layers. [15][16][17] A promising approach that dramatically improves the light output power is electron-beam (e-beam) pumping, especially for the short-wavelength UVC spectral range. [3,[18][19][20][21][22][23][24] This approach allows one to bypass the need for p-type or n-type injection layers and, thus, can largely increase the carrier injection efficiency. This provides a unique advantage over conventional LEDs at UVC range, since the p-type doping for high-Al-content AlGaN is High-output-power electron-beam (e-beam) pumped deep ultraviolet (DUV) light sources, operating at 230-270 nm, are achieved by adjusting the well thickness of binary ultrathin GaN/AlN multiple quantum wells. These structures are fabricated on high-quality thermally annealed AlN templates by metal-organic chemical vapor deposition. Owing to the reduced dislocation density, large electron-hole overlap, and efficient carrier injection by e-beam, the DUV light sources demonstrate high output powers of 24.8, 122.5, and 178.8 mW at central wavelengths of 232, 244, and 267 nm, respectively. Further growth optimization and employing an e-gun with increased beam current lead to a record output power of ≈2.2 W at emission wavelength of ≈260 nm, the key wavelength for water sterilization. This work manifests the practical levels of high-output-power DUV light sources operated by using e-beam pumping method. The ORCID identification number(s) for the author(s) of this article can be found under https://doi.org/10.1002/adom.201801763.Solid-state deep ultraviolet (DUV) optoelectronic devices in the spectral range of 200-280 nm, i.e., ultraviolet-C (UVC), have attracted much attention for their wide applications in sterilization, medical treatment, security, solar-blind photodetection, and so on. [1][2][3][4][5][6][7] Currently, Al(Ga)N material system is the most promising candidate for solid-state UVC light sources

Quasi-2D GaN layers inserted in an AlGaN matrix are proposed as a novel active region to develop a high-output-power UV light source. Such a structure is successfully achieved by precise control in molecular beam epitaxy and shows an amazing output power of ≈160 mW at 285 nm with a pulsed electron-beam excitation. This device is promising and competitive in non-line-of-sight communications or the sterilization field.

We report the internal structures and emission properties of GaN/AlN single- and multiple-quantum-well (QW) heterostructures with well widths of dw = 1–4 monolayers (MLs), grown by plasma-assisted molecular-beam epitaxy on c-sapphire at metal-rich conditions and low temperatures (∼700 °C). The formation of plane QWs with abrupt symmetrical interfaces is confirmed by both scanning transmission electron microscopy and X-ray diffraction analysis. Pulse-scanning and continuous-wave output powers of 150 and 28 mW, respectively, at a peak emission wavelength of 235 nm were achieved at 300 K in an electron-beam-pumped deep-ultraviolet (1.5 ML-GaN/5.5 nm-AlN)360 multiple-QW emitter with a maximum efficiency of 0.75%.