Human exposure to air pollution and especially to nanoparticles is increasing due to the combustion of carbon-based energy vectors. Fibrous filters are among the various types of equipment potentially able to remove particles from the air. Nanofibers are highly effective in this area; however, their utilization is still a challenge due to the lack of studies taking into account both nanoparticle collection efficiency and antibacterial effect. The aim of this work is to produce and evaluate novel silver/polyacrylonitrile (Ag/PAN) electrospun fibers deposited on a nonwoven substrate to be used as air filters to remove nanoparticles from the air and also showing antibacterial activity. In order to determine the optimum manufacturing conditions, the effects of several electrospinning process parameters were analyzed such as solution concentration, collector to needle distance, flow rate, voltage, and duration. Ag/PAN nanofibers were characterized by Xray diffraction (XRD), Transmission Electron Microscopy (TEM), Fourier Transform Infra-Red spectroscopy (FTIR), Energy-dispersive X-ray spectroscopy (EDX), X-ray photoelectron spectroscopy (XPS), and Scanning Electron Microscopy (SEM). In addition, filtration performances were determined by measuring the pressure drop and collection efficiency of sodium chloride (NaCl) aerosol particles (9 to 300 nm diameters) using Scanning Mobility Particle Sizers (SMPS). Filters with high filtration efficiency (≈100%) and high-quality factor (≈0.05 Pa -1 ) were obtained even adding different concentrations of Ag nanoparticles (AgNPs) to PAN nanofibers. The resultant Ag/PAN nanofibers showed excellent antibacterial activity against 10 4 CFU/ml E.coli bacteria.The crystallinity of the silver nanoparticles was analyzed using X-ray diffraction analysis and shown in Figure S1. The peak observed at 17° for the 0AgF samples corresponds to (110) plan of PAN. Crystalline peak corresponds to silver nanoparticles were absent in all samples (1AgF, 10AgF, and 50AgF) which is due to the small size (<5nm) of silver nanoparticles.

Often, solid matter is separated from particle-laden flow streams using electrospun filters due to their high specific surface area, good ability to capture aerial particulate matter, and low material costs. Moreover, electrospinning allows incorporating nanoparticles to improve the filter’s air filtration efficiency and bacterial removal. Therefore, a new, improved polyacrylonitrile (PAN) nanofibers membrane that could be used to remove air pollutants and also with antibacterial activity was developed. We engineered three different filters that are characterized by the different particles embedded in the PAN nanofibers: titanium dioxide (TiO2), zinc oxide (ZnO), and silver (Ag). Then, their filtration performance was assessed by quantifying the filtration of sodium chloride (NaCl) aerosol particles of 9 to 300 nm in diameter using a scanning mobility particle sizer. The TiO2_F filter displayed the smallest fiber diameter and the highest filtration efficiency (≈100%). Conversely, the Ag_F filter showed the highest quality factor (≈0.06 Pa−1) because of the lower air pressure drop. The resulting Ag_F nanofibers displayed a very good antibacterial activity using an Escherichia coli suspension (108 CFU/mL). Moreover, the quality factor of these membranes was higher than that of the commercially available nanofiber membrane for air filtration.

No abstract

To this day, any photosensitizers for the photodynamic treatment of pulmonary illnesses have been administered intravenously. There is, however, an intrinsic difficulty in reaching the target cells or bacteria in the respiratory system. Nebulization could overcome distribution problems and alleviate side effects by delivering the photosensitizers directly to the lungs. In this study, we evaluated the viability of three photosensitizers (indocyanine green, the chlorine Photodithazine®, and the porphyrin Photogem®) was evaluated comparatively in a jet nebulizer. Quantitative analysis was performed by looking at the droplet size, extent of nebulization, output over time, and stability of the solutions. All of the tested photosensitizers were found to be adequately nebulized. We also demonstrated the delivery of indocyanine green to the pulmonary tract and its activation with infrared light in a murine model using extracorporeal detection of fluorescence. This was an important step towards clinical implementation of the extracorporeally-illuminated photodynamic inactivation of pneumonia, recently demonstrated in vivo by this research group. This article is protected by copyright. All rights reserved.

The development of new materials with specific functionalities for certain applications has been increasing with the advent of nanotechnology. A technique widely used for this purpose is electrospinning, because control of several parameters involved in the process can yield nanoscale fibers. In addition to the production of innovative and small-scale materials, through structural, chemical, physical, and biological modifications in the fibers produced in electrospinning, it is possible to obtain specific properties for a given application. Thus, the produced fibers can serve different purposes, such as in the areas of sensors, catalysis, and environmental and medical fields. Given this context, this article presents a review of the electrospinning technique, addressing the parameters that influence the properties of the fibers formed and some techniques used to modify them as specific treatments that can be conducted during or after electrospinning. In situ addition of nanoparticles, changes in the configuration of the metallic collector, use of alternating current, electret fibers, core/shell method, coating, electrospray-coating, plasma, reinforcing composite materials, and thermal treatments are some of the examples addressed in this work. Therefore, this work contributes to a better comprehension of some of the techniques mentioned in the literature so far.