Here, a simple but effi cient way is demonstrated for the preparation of nanoporous graphene enriched with Fe/Co-nitrogen-doped active sites (Fe/Co-NpGr) as a potential electrocatalyst for the electrochemical oxygen reduction reaction (ORR) applications. Once graphene is converted into porous graphene (pGr) by a controlled oxidative etching process, pGr can be converted into a potential electrocatalyst for ORR by utilizing the created edge sites of pGr for doping nitrogen and subsequently to utilize the doped nitrogens to build Fe/Co coordinated centers (Fe/Co-NpGr). The structural information elucidated using both XPS and TOF-SIMS study indicates the presence of coordination of the M-N (M = Fe and Co)-doped carbon active sites. Creation of this bimetallic coordination assisted by the nitrogen lockedat the pore openings is found to be helping the system to substantially reduce the overpotential for ORR. A 30 mV difference in the overpotential ( η ) with respect to the standard Pt/C catalyst and high retention in half wave potential after 10 000 cycles in ORR can be attained. A single cell of an anion exchange membrane fuel cell (AEMFC) by using Fe/Co-NpGr as the cathode delivers a maximum power density of ≈35 mWcm −2 compared to 60 mWcm −2 displayed by the Pt-based system.

Transition metal oxide derived materials are very important for various applications, such as electronics, magnetism, catalysis, electrochemical energy conversion, and storage. Development of efficient and durable catalysts for the oxygen reduction reaction (ORR), an important reaction in fuel cells and metal–air batteries, is highly desirable. Moreover, the futuristic catalysts for these applications need to be cost-effective in order to ensure a competitive edge for these devices in the energy market. This article describes the synthesis of a cost-effective and efficient electrocatalyst for ORR. It is based on supporting CoMn alloy oxide nanoparticles on N-doped porous graphene through a simple and scalable microwave irradiation method. Microwave irradiation was found to be very crucial for the fast creation of pores in the graphene framework with a concomitant formation of the CoMn alloy oxide nanoparticles. A series of catalysts have been synthesized by varying the Co:Mn ratio, among which, the one with the Co:Mn ratio of 2:1 [designated as CoMn/pNGr(2:1)] displayed remarkably higher ORR activity in 0.1 M KOH solution. It showed a ∼60 mV potential shift with a low Tafel slope of 74 mV/decade, which is comparable to that derived from the commercial Pt/C catalyst. This high activity of CoMn/pNGr(2:1) has been credited to the cooperative effect arising from the metal entities and the defects present in the N-doped porous graphene. Finally, real system-level validations of the use of CoMn/pNGr(2:1) as cathode catalyst could be performed by fabricating and testing single-cells of an anion-exchange membrane fuel cell (AEMFC) and a primary Zn–air battery, which successfully demonstrated the efficiency of the catalyst to facilitate ORR in real integrated systems of the single-cell assemblies.

Earth abundant, first row transition metals offer a cheap and sustainable alternative to the rare and precious metals. However, utilization of first row metals in catalysis requires harsh reaction conditions, suffers from limited activity, and fails to tolerate functional groups. Reported here is a highly efficient iron catalyzed hydroformylation of alkenes under mild conditions. This protocol operates at 10-30 bar syngas pressure below 100 °C, utilizes readily available ligands, and applies to an array of olefins. Thus, the iron precursor [HFe(CO)][PhPNPPh] (1) in the presence of triphenyl phosphine catalyzes the hydroformylation of 1-hexene (S2), 1-octene (S1), 1-decene (S3), 1-dodecene (S4), 1-octadecene (S5), trimethoxy(vinyl)silane (S6), trimethyl(vinyl)silane (S7), cardanol (S8), 2,3-dihydrofuran (S9), allyl malonic acid (S10), styrene (S11), 4-methylstyrene (S12), 4- iBu-styrene (S13), 4- tBu-styrene (S14), 4-methoxy styrene (S15), 4-acetoxy styrene (S16), 4-bromo styrene (S17), 4-chloro styrene (S18), 4-vinylbenzonitrile (S19), 4-vinylbenzoic acid (S20), and allyl benzene (S21) to corresponding aldehydes in good to excellent yields. Both electron donating and electron withdrawing substituents could be tolerated and excellent conversions were obtained for S11-S20. Remarkably, the addition of 1 mol % acetic acid promotes the reaction to completion within 16-24 h. Detailed mechanistic investigations revealed in situ formation of an iron-dihydride complex [HFe(CO)(PPh)] (A) as an active catalytic species. This finding was further supported by cyclic voltammetry investigations and intermediacy of an Fe(0)-Fe(II) species was established. Combined experimental and computational investigations support the existence of an iron-dihydride as the catalyst resting state, which then follows a Fe(II) based catalytic cycle to produce aldehyde.

Solvothermal synthesis of zirconium-substituted cobalt ferrite nanoparticles was accomplished by the introduction of zirconium (Zr) in the spinel matrix to obtain a cost-effective and robust electrocatalyst that does not use noble metals. A variation in the cobalt ferrite structure CoFe 2−x Zr x O 4 with Zr (0.1−0.4) substitution has significantly altered the overpotential for the electrocatalytic oxygen reduction reaction (ORR) and oxygen evolution reaction (OER), leading to an optimum composition of CFZr(0.3). The incorporation of the foreign Zr 4+ ion in the cobalt ferrite spinel lattices has effectively enhanced the oxygen evolution reaction (OER) activity in comparison to the parent cobalt ferrite (CF) nanocrystals. However, a nominal change in the ORR current density has been observed due to Zr incorporation. For the OER, the Zr-substituted catalyst has shown a 40 mV negative shift in the overpotential in comparison with the CF nanoparticles at 10 mA/cm 2 current density. Interestingly, the in situ grafting of Zr-substituted cobalt ferrite nanoparticles over N-doped reduced graphene oxide (CFZr(0.3)/N-rGO) results in remarkably enhanced performance during the ORR and moderately favored the OER with an overall potential difference (ΔE) of 0.840 V. The enhanced bifunctional electrocatalytic activity of the material is crucial for the fabrication of high-performance rechargeable Zn−air batteries (ZABs). The prepared catalyst exhibited an overpotential of 80 mV for the ORR in comparison with the state-of-the-art (Pt/C) catalyst and an overpotential of 340 mV at 10 mA/cm 2 current density for the OER from the standard value (1.23 V vs RHE). This potential bifunctional electrocatalyst has been employed as an electrode material for the fabrication of a primary ZAB, where it exhibited discharge capacities of 727 and 730 mAh/g at current densities of 20 and 30 mA/cm 2 , respectively, under ambient conditions. The notable performance of the catalyst as a bifunctional material is observed during the cycling of the rechargeable ZAB. The prepared catalyst showed an increase of 200 mV in the overall operating overpotential after cycling for 10 cycles at 15 mA/cm 2 in comparison to the 350 mV increase shown by the Pt/C catalyst.