This paper provides a detailed description of complex bainitic microstructures obtained during the recent development of low carbon linepipe steels with strengths in the range of X100 to X120. New experimental techniques based on a high resolution FEG-SEM and EBSD have been used to characterise and quantify the mixture of ultrafine bainitic ferrite and nanosize second phases in these steels. It was found that the occurrence of incomplete transformation generates new, previously unexplored bainitic microstructures with a wealth of microstructural features that is beyond classification based on conventional concepts. Clear differences in distributions of boundary misorientations and effective grain size were noted between upper, lower and granular bainites. Based on these results a new classification scheme and definition of bainite is proposed.

The increasing demand for natural gas will further influence the type of its transportation in the future, both from the strategic and economic point of view. Long-distance pipelines are a safe and economic means to transport the gas from production sites to end users. High-strength steels in grade X80 are nowadays state of the art. Grade X100 was recently developed but not yet utilised. The present-day technical limitations on the production of X120 line pipe namely the steel composition, the pipe forming and the welding are addressed in this paper. Production test results on X120 pipes are presented to describe the materials properties. A low carbon and low PCM steel with VNbTiB microalloying concept is used. In the plate rolling the main attention is turned to the heavy accelerated cooling. The large spring back that occurs during the U-forming step of the UOE process is one of the most complex aspects in forming X120. To handle this aspect FEM calculations were used to modify the forming parameters and to optimise the shape of the U-press tool. For optimising the existing welding procedure with respect to an avoidance of HAZ softening, a low heat input welding technology and new welding consumables were developed.

No abstract

Recently, advanced thermomechanical hot rolling schedules followed by direct quenching are being developed in order to avoid reheating and quenching treatment after hot rolling to eliminate an energy and cost consuming step. The use of boron as an alloying element is a widely known practice in high strength medium carbon steels to increase the strength due its potential for delaying phase transformation and improving hardenability. In addition, a significant synergetic effect on hardenability could be reached combining B with microalloying elements (adding Nb, Mo or Nb-Mo). With the purpose of exploring the effect of microalloying elements and thermomechanical rolling schedule, laboratory thermomechanical simulations reproducing plate mill conditions were performed using ultra high strength steels micro-alloyed with Nb, Mo, and Nb-Mo. To that end, plane compression tests were performed, consisting of an initial preconditioning step, followed by several roughing and finishing deformation passes and a final quenching step. After fast cooling to room temperature, a tempering treatment was applied. In the present paper, the complex interaction between the martensitic microstructure, the tempering treatment, the addition of microalloying elements, and the resulting tensile properties was evaluated. For that purpose, an exhaustive EBSD quantification was carried out in both quenched as well as quenched and tempered states for all the steel grades and the contribution of different strengthening mechanisms on yield strength was analyzed. Highest tensile properties are achieved combining Nb and Mo, for both quenched (Q) and quenched and tempered states (Q&T), reaching yield strength values of 1107 MPa and 977 MPa, respectively. Higher tempering resistance was measured for the Mo-bearing steels, making the CMnNbMoB steel the one with the lowest softening after tempering. For CMnB grade, the yield strength reduction after tempering of about 413 MPa was measured, while for NbMo micro-alloyed steel, yield strength softening is considerably reduced to 130 MPa.

The synergetic effect on hardenability by combining boron with other microalloying elements (such as Nb, Mo and Nb + Mo) is widely known for high-strength medium carbon steels produced by direct quenching and subsequent tempering treatment. The improvement of mechanical properties could be reached through optimization of different mechanisms, such as solid solution hardening, unit size refinement, strain hardening, fine precipitation hardening and the effect of carbon in solid solution. The current study proposes a procedure for evaluating the contribution of different microstructural aspects on Charpy impact toughness. First, the effect that austenite conditioning has on low-temperature transformation unit sizes and microstructural homogeneity was analysed for the different microalloying element combinations. A detailed crystallographic characterization of the tempered martensite was carried out using electron backscattered diffraction (EBSD) in order to quantify the effect of unit size refinement and dislocation density. The impact of heterogeneity and presence of carbides was also evaluated. The existing equations for impact transition temperature (ITT50%) predictions were extended from ferrite-pearlite and bainitic microstructures to tempered martensite microstructures. The results show that microstructural refinement is most beneficial to strength and toughness while unit size heterogeneity has a particularly negative effect on ductile-to-brittle transition behaviour. By properly balancing alloy concept and processing, steel having a yield strength above 900 MPa and low impact transition temperature could be obtained by direct quenching and tempering.