Ground improvement is an effective method of mitigation to improve problematic soils including soft kaolin clay soils.Implementation of industrial wastes such as bottom ash in ground improvement can be cost-effective and environment-friendly.There are several studies conducted on the granular column using the bottom ash column. However, only a few studies have reported ndings coherent with the statistical analysis. In this study, the lateral load capacity of bottom ash column-kaolin clay has been conducted. Coherently, the reinforced kaolin clay samples were tested via Particle Size Distribution, Atterberg limit test, Relative Density, Compaction test, Permeability test, Uncon ned Compression Test and Unconsolidated Undrained Triaxial Test with the single and group encapsulated bottom ash with the geotextile encasement and a prediction model was developed. The effect of a number of columns, column diameter, column height, area replacement ratio, height penetration ratio, height-diameter column ratio, volume replacement ratio and con ning pressures on the shear strength of the single and group of encapsulated bottom ash columns have been investigated. The ndings showed the effectiveness of using the bottom ash columns to enhance the shear strength of the soil up to 77.00%.

Thin-film composite (TFC) is feasible for use in isopropanol (IPA) dehydration by pervaporation (PV) for its superior performance and strength. The hydrophobic substrate membrane allows the penetration of the diamine monomer into the pores, which leads to flux reduction. Furthermore, hydrophobic polymer is difficult for TFC deposition because of its strong and opposing characteristics. To solve this problem, hydrophilic nylon 6,6 (N66) was introduced as a substrate in this application because of the balanced characteristics such as small distribution pores, great interaction with polyamide layer, and high mechanical strength to overcome the swelling weakness. TFC membranes were prepared by interfacial polymerisation (IP) method between m-phenylenediamine (MPD) and trimesoyl chloride (TMC) monomer. The chemical and physical properties were characterised by scanning electron microscopy (SEM), Fourier-transform infrared (FTIR) spectroscopy, contact angle, and swelling test analyses. A fully aromatic polyamide group was detected at FTIR spectrum 1609e1610 cm À1 . Increasing the immersion time from 2 to 5 min in 2 wt % MPD and 1 min immersion in 0.1 wt % TMC solutions increased the thickness of the membranes from 40.0 to 56.3 mm. The contact angle decreased significantly from 50 to 35 after the modification, thereby obtaining better hydrophilic properties for interface to occur. In addition, continuous IPA sorption experiments for up to 24 h were carried out for pristine N66 and TFC membranes, using 60, 80 and 90 wt % IPA/water solutions. The degree of swelling increased with time as the water composition increased.

No abstract

Effect of adipic acid concentration on the isotactic polypropylene flat sheet using methyl salicylate prepared by TIPS for CO 2 /N 2 separation.

The thin film composite (TFC) membrane is a porous membrane layered by a polyamide active layer. In the experimental work, the polyamide active layer prepared by the interaction between monomers, m-phenylenediamine (MPD) and trimesoyl chloride (TMC) which deposited on a membrane support. Considering the possibility of producing a loose TFC membrane and affect the separation performance, this study enlightens the interaction between monomers with Nylon 6 6 (N66) support membrane using simulation - molecular dynamic (MD). Different simulation system has been investigated with varying the ratio molecule of MPD to TMC where, TFC1 (1:1), TFC2 (3:1) and TFC3 (3:2) to the tertiary system of N66/MPD/TMC. The simulation was set for a COMPASS force field, where the equilibrium phases in a microcanonical (constant volumes and total energy) (NVE) followed by run-production stage (constant pressure and temperature ensembles) (NPT) ensembles. The temperature and pressure were set at 323.15 K and 1atm respectively. The polyamide TFC was found to be formed by the main interactions between nitrogen (N) from MPD group to the carbon, (C) from TMC main chain at ranges of 4.25Å. Overall interaction can be observed between N from TFC layer with O atom from the substrate layer. All of the intermolecular interactions take place at 3.25Å distance. The best interaction in N66 to MPD and TMC system to the weakest is in the arrangement of TFC2 > TFC3 > TFC1. The highest intensity was obtained by the TFC2, indicating the best ratio of 3:1 of MPD molecules to TMC molecule with support polymer when fully polymerized occurred. This study suggests that ratio N66 to MPD and TMC in TFC2 is the best to interaction between TFC layer and substrate for fabrication of the TFC membrane.