Objective To investigate the bone hardness of different anatomical regions of the human radius and its impact on the pullout strength of screws. Methods Fresh radius bones were obtained from three donated cadavers. They were divided into three parts: proximal metaphysis, shaft, and distal metaphysis. The proximal metaphysis contains the head, neck, and radial tuberosity. The distal metaphysis includes the palmaris radius and the styloid process. The shaft of the radius was divided into nine segments of equal length. The bone hardness of three radiuses, one from each cadaver, was measured by Vickers microindentation hardness tests, and the screw pullout strength was examined in the other three radiuses using a materials testing machine. The trend between radius hardness and pullout strength was analyzed by using an analysis of variance randomized block design. Pearson correlation analysis was performed to evaluate the linear correlation between the bone hardness and the pullout strength of the human radius. Results The mean hardness ranged from 33.30 HV (the head) to 43.82 HV (the diaphysis). The hardest part of the radius was the shaft, with a value of 42.54 ± 5.59 HV. The proximal metaphysis had a hardness value of 34.15 ± 6.48 HV, and the distal metaphysis hardness value was 35.24 ± 5.17 HV. The shaft was 23.5% harder than the proximal metaphysis and 20% harder than the distal metaphysis. The microhardness test demonstrated that the bone hardness value of the diaphysis was significantly higher than those of both the proximal and distal metaphysis of the radius (both P < 0.05). The mean pullout strength values ranged from 552 N (the distal metaphysis) to 2296 N (the diaphysis). The greatest pullout strength of the radius was observed for the shaft, with a pullout strength of 1727.96 ± 111.44 N. The pullout strength of the proximal metaphysis was 726.33 ± 236.39 N, and the pullout strength of the distal metaphysis was 590.67 ± 36.30 N. The pullout strength of the shaft was 138% greater than that of the proximal metaphysis and 190% greater than that of the distal metaphysis. The pullout strength was also higher in the diaphysis than at both ends of the radius (both P < 0.05). A positive correlation was found between bone hardness and pullout strength (R = 0.927, P < 0.001). Conclusions Bone hardness and screw pullout strength are higher in the diaphysis of the radius than at either end. The pullout strength is positively related to bone hardness in the human radius.

No abstract

Both spiral plate and Herbert screw fixations have been clinically adopted for treating midshaft displaced clavicle fractures. However, the biomechanical properties of the 2 implant fixations have not yet been thoroughly evaluated. Here we report the results of a finite element analysis of the biomechanical properties of midshaft clavicle fractures treated with Herbert screw and spiral plate fixation. Hebert screw fixation showed stress distribution similar to intact clavicle under all loading conditions, but provided less stability than did spiral plate fixation. Postoperatively, excessive shoulder activities and weight-bearing should be avoided. Spiral plate fixation provides greater stability, but is associated with stress shielding. These results demonstrate that Herbert screw fixation is suitable for the treatment of simple displaced clavicluar fractures, but excessive shoulder activity and weight-bearing should be avoided after the operation. Therefore, spiral plate fixation may be preferred for patients requiring an early return to activity.

Indentation hardness test is a good in vitro method of bone quality assessment. The purpose of this study is to explore the distribution characteristics of bone tissue microhardness in tibial diaphysis and provide theoretical support for the test site selection of the reference point indentation technique. Three fresh right tibias were obtained from 3 cadaver donors. The tibial diaphysis was evenly divided into 6 sections. Bone specimens with a thickness of 3 mm were cut from each part. After appropriate management, micro-indentation tests were performed in various regions of the specimens to acquire the microhardness values of the tibial diaphysis. Statistical analysis was performed by randomized block design variance analysis to study the distribution characteristics of bone microhardness. 72 regions were selected for 360 effective indentations. We found that the bone microhardness is inhomogeneous in tibia diaphysis. Mean hardness value of the anterior, medial, posterior, lateral region of tibia diaphysis was 45.58 ± 4.39 Vickers hardness (HV), 52.33 ± 3.93 HV, 54.00 ± 4.21 HV, 52.89 ± 4.44 HV, respectively. The anterior cortex exhibits lower microhardness value than the other regions ( P < .001). Within the same region, microhardness varies significantly with positions in the tibial diaphysis. The variations in indentation hardness are bound to have a significant impact on the comparability of different reference point indentation (RPI) studies. The results of this study indicated the regional microhardness difference in the human tibia diaphysis. The microhardness of different planes in the same region is also inconsistent. Inhomogeneous distribution of indentation microhardness would have considerable influence in the test site selection of RPI technique. The data collected in our study would contribute to the design of highly precise 3D printing implants and bionic bones with gradient elastic modulus.