Background Patients with unilateral cleft lip and palate were associated with different nasomaxillary complex from the normal population. Although the biomechanical effects of conventional rapid palatal expansion (Hyrax expansion) and bone-borne rapid palatal expansion (micro-implant-assisted expansion) in non-cleft patients have been identified by multiple studies, little is known in patients with unilateral cleft lip and palate. The purpose of this study was to investigate and compare the biomechanical effects of the conventional and bone-borne palatal expanders in a late adolescence with unilateral cleft lip and palate. Methods A cone beam CT scan of a late adolescence with unilateral cleft lip and palate was selected to construct the three-dimensional finite element models of teeth and craniofacial structures. The models of conventional and born-borne palatal expanders were established to simulate the clinical maxillary expansion. The geometric nonlinear theory was applied to evaluate the Von Mises stress distribution and displacements in craniofacial structures and teeth. Results Bone-borne palatal expander achieved more transverse movement than conventional palatal expander in the whole mount of craniofacial regions, and the maximum amount of expansion was occurred anteriorly along the alveolar ridge on cleft-side. The expanding force from born-borne palatal expander resulted in more advancement in nasomaxillary complex than it in conventional palatal expander, especially in the anterior area of the minor segment of maxilla. Stresses from the both expanders distributed in similar patterns, but larger magnitudes and ranges were generated using the bone-borne expander around the maxillary buttresses and pterygoid plates of sphenoid bone. The maximum expanding stresses from born-borne palatal expander were concentrated on palatal slope supporting minscrews, whereas those from conventional palatal expander were concentrated on the anchoring molars. In addition, the buccal tipping effect of teeth generated using the bone-borne expander was less than it using the conventional palatal expander. Conclusion Bone-borne expander generated enhanced skeletal expansion at the levels of alveolar and palate in transversal direction, where the miniscrews contributed increased expanding forces to maxillary buttresses and decreased forces to buccal alveolar. Bone-borne expanders presented a superiority in correcting the asymmetric maxilla without surgical assistant in late adolescence with unilateral cleft lip and palate.

The purpose of this study was to develop a novel Bonwill Hawley method (Bonwill Hawley arch form based on CBCT image) for the assessment of dental crowding, and to investigate and compare the accuracy and eligibility with the conventional brass wire and caliper methods under different crowding conditions. Material and methods60 patients with the pair of plaster casts and CBCT data were collected. All the casts were marked and transformed into digital models using iTero scanner, and imported into OrthoCAD software to measure the required space. Using the conventional brass wire (M1) and caliper methods (M2), the available space and dental crowding were measured and calculated basing on digital models, respectively.Correspondingly, the axial planes in the level of dental arches were oriented and captured from the CBCT images to draw the Bonwill Hawley arch forms (M3), which were used to measure and calculate the available space and dental crowding. For each method, intra and inter-examiner reliabilities were elevated with intra-class correlation coe cients (ICCs). Wilcoxon test and Kruskal-Wallis test were performed for statistically analyzing the discrepancy among different groups. ResultsBoth intra and inter-examiner reliability were generally excellent for all parameters obtained by the three methods, except for the dental crowding measured using M1(ICC: 0.473/0.261). The dental crowding measured using M2 were signi cantly increased in mild, moderate and severe-crowding groups compared with M1. However, no signi cant difference was detected between M1 and M3 in severe-crowding group (maxilla, p = 0.108 > 0.05; mandible, p = 0.074 > 0.05). With the deteriorate of crowding condition, the discrepancy of dental crowding between M1 and M2, or M1 and M3 were signi cantly decreased (maxilla,

Objectives The purpose of this study was to develop a novel Bonwill⁃Hawley method (Bonwill⁃Hawley arch form based on CBCT image) for the assessment of dental crowding, and to investigate and compare the accuracy and eligibility with the conventional brass wire and caliper methods under different crowding conditions. Material and methods 60 patients with the pair of plaster casts and CBCT data were collected. All the casts were marked and transformed into digital models using iTero scanner, and imported into OrthoCAD software to measure the required space. Using the conventional brass wire (M1) and caliper methods (M2), the available space and dental crowding were measured and calculated basing on digital models, respectively. Correspondingly, the axial planes in the level of dental arches were oriented and captured from the CBCT images to draw the Bonwill⁃Hawley arch forms (M3), which were used to measure and calculate the available space and dental crowding. For each method, intra and inter-examiner reliabilities were elevated with intra-class correlation coefficients (ICCs). Wilcoxon test and Kruskal-Wallis test were performed for statistically analyzing the discrepancy among different groups. Results Both intra and inter-examiner reliability were generally excellent for all parameters obtained by the three methods, except for the dental crowding measured using M1(ICC: 0.473/0.261). The dental crowding measured using M2 were significantly increased in mild, moderate and severe-crowding groups compared with M1. However, no significant difference was detected between M1 and M3 in severe-crowding group (maxilla, p = 0.108 > 0.05; mandible, p = 0.074 > 0.05). With the deteriorate of crowding condition, the discrepancy of dental crowding between M1 and M2, or M1 and M3 were significantly decreased (maxilla, M2-M1, mild VS serve, p = 0.003 < 0.05; maxilla, M3-M1, mild VS serve, p = 0.003 < 0.05; mandible, M2-M1, mild VS serve, p = 0.000 < 0.001; mandible, M3-M1, mild VS serve, p = 0.043 < 0.05). Conclusion Dental crowding measured using the novel Bonwill⁃Hawley method was relatively greater than the caliper method, but not exceeding the brass wire method, which wound gradually come close to the brass wire method with the deteriorate of crowding condition. Clinical relevance : The Bonwill⁃Hawley method basing on CBCT image proved to be a reliable and acceptable choice for orthodontists to analyze the dental crowding.