A detailed study and comparison was made on the catalytic activities of cutinases from Humilica insolens (HiC), Pseudomonas mendocina (PmC), and Fusarium solani (FsC) using low-crystallinity (lc) and biaxially oriented (bo) poly(ethylene terephthalate) (PET) films as model substrates. Cutinase activity for PET hydrolysis was assayed using a pH-stat to measure NaOH consumption versus time, where initial activity was expressed as units of micromoles of NaOH added per hour and per milliliter of reaction volume. HiC was found to have good thermostability with maximum initial activity from 70 to 80 °C, whereas PmC and FsC performed best at 50 °C. Assays by pH-stat showed that the cutinases had about 10-fold higher activity for the lcPET (7% crystallinity) than for the boPET (35% crystallinity). Under optimal reaction conditions, initial activities of cutinases were successfully fit by a heterogeneous kinetic model. The hydrolysis rate constant k 2 was 7-fold higher for HiC at 70 °C (0.62 μmol/cm2/h) relative to PmC and FsC at 50 and 40 °C, respectively. With respect to PET affinity, PmC had the highest affinity, while FsC had the lowest value. In a 96 h degradation study using lcPET films, incubation with PmC and FsC both resulted in a 5% film weight loss at 50 and 40 °C, respectively. In contrast, HiC-catalyzed lcPET film hydrolysis at 70 °C resulted in a 97 ± 3% weight loss in 96 h, corresponding to a loss in film thickness of 30 μm per day. As degradation of lcPET progressed, crystallinity of the remaining film increased to 27% due to preferential degradation of amorphous regions. Furthermore, for all three cutinases, analysis of aqueous soluble degradation products showed that they consist exclusively of terephthalic acid and ethylene glycol.

This paper describes the synthesis, crystal structure, and physicomechanical properties of a biobased polyester prepared from 2,5-furandicarboxylic acid (FDCA) and 1,4-butanediol. Melt-polycondensation experiments were conducted by a two-stage polymerization using titanium tetraisopropoxide (Ti[OiPr] 4 ) as a catalyst. Polymerization conditions (catalyst concentration, reaction time and second stage reaction temperature) were varied to optimize poly(butylene-FDCA), PBF, and molecular weight. A series of PBFs with different M w were characterized by DSC, TGA, DMTA, X-ray diffraction and tensile testing. Influence of molecular weight and melting/ crystallization enthalpy on PBF material tensile properties was explored. Cold-drawing tensile tests at room temperature for PBF with M w 16K to 27K showed a brittle-to-ductile transition. When M w reaches 38K, the Young modulus of PBF remains above 900 MPa, and the elongation at break increases to above 1000%. The mechanical properties, thermal properties and crystal structures of PBF were similar to petroleum derived poly(butylenes-terephthalate), PBT. Fiber diagrams of uniaxially stretched PBF films were collected, indexed, and the unit cell was determined as triclinic (a = 4.78(3) Å, b = 6.03(5) Å, c = 12.3(1) Å, α = 110.1(2)°, β = 121.1(3)°, γ = 100.6(2)°). A crystal structure was derived from this data and final atomic coordinates are reported. We concluded that there is a close similarity of the PBF structure to PBT αand β-forms.

Omega-hydroxyfatty acids are excellent monomers for synthesizing a unique family of polyethylene-like biobased plastics. However, ω-hydroxyfatty acids are difficult and expensive to prepare by traditional organic synthesis, precluding their use in commodity materials. Here we report the engineering of a strain of the diploid yeast Candida tropicalis to produce commercially viable yields of ω-hydroxyfatty acids. To develop the strain we identified and eliminated 16 genes encoding 6 cytochrome P450s, 4 fatty alcohol oxidases, and 6 alcohol dehydrogenases from the C. tropicalis genome. We also show that fatty acids with different chain lengths and degrees of unsaturation can be more efficiently oxidized by expressing different P450s within this strain background. Biocatalysis using engineered C. tropicalis is thus a potentially attractive biocatalytic platform for producing commodity chemicals from renewable resources.