Materials that possess distinguishable superwettability toward oil and water have aroused widespread attention for their application in oil–water separation. Among them, a superoleophobic/superhydrophilic material is considered as the ideal candidate because of its antioil-fouling and water-wetting behavior; however, the fabrication is a challenge and there has been insufficient attention given to multipurpose applications in treating intricate mixtures. Herein, for the first time, a multifunctional superoleophobic/superhydrophilic coating integrated with a photocatalysis property was fabricated by the combination of polarity component-enhanced fluorosurfactant and titanium dioxide (TiO2) nanoparticles. The coating applied on stainless steel mesh preserves the ability to separate immiscible oil–water mixtures, whereas the coated cotton preserves the ability to separate both surfactant-stabilized oil-in-water and water-in-oil emulsions. Notably, benefiting from the photocatalysis property of titanium dioxide, the coating also can be used in liquid purification. Contaminated oil can be separated and purified by a separation–purification process, during which the oil-soluble contamination is degraded under ultraviolet (UV) irradiation. The multipurpose coating provides an alternative solution for oil–water remediations, which has prospects in intricate liquid treatment in industrial and domestic applications.

No abstract

The superoleophobic/superhydrophilic material has attracted considerable interest due to the incomparable property of it for the oil–water separation. However, it is a challenge to make the prepared surface superoleophobic and superhydrophilic at the same time since the oleophobic surface tends to repel water. Herein, a hygro-responsive superoleophobic/superhydrophilic coating was fabricated by liquid-phase deposition of TiO2 with perfluorooctanoic acid. The wettability of the coating could complete the transformation from superoleophobicity/superhydrophilicity to superhydrophobicity/superoleophilicity, both of which exhibit excellent selective superwettability under the air, underwater, salt, alkali, and acid conditions. The hygro-responsive coating can separate different types of oil–water mixtures, and the separation efficiency could be over 99% using different capillary forces acting on the oil and water phases before and after wettability transformation. Last but not least, long-chain perfluoroalkyl substances on the coating could be decomposed by UV irradiation, which could reduce the harm to the environment and human beings. It is anticipated that the developed superoleophobic/superhydrophilic coating provides a feasible solution for the application of oil–water separation.

Controllable wettability is important for a wide range of applications, including intelligent switching, self-cleaning and oil/water separation. In this work, rapid switching and extreme wettability changes upon ultraviolet (UV) illumination were investigated. TiO2 nanoparticles were modified in solutions of trimethoxy(alkyl)silane, and the suspensions were sprayed on glass substrates. For such samples, the water contact angle (WCA) was shown to transition from a superhydrophobic (WCA ≈ 165°) to a superhydrophilic (WCA ≈ 0°) state within 10 min upon UV illumination and subsequent recovery to superhydrophobicity occurred after heat treatment. It was found that the changes in the trimethoxy(alkyl)silane upon UV illumination can explain the rapid decrease of the WCA from more than 165° to almost 0°. To further investigate the wettability transition, trimethoxy(alkyl)silane and Al2O3 nanoparticles (which are not photocatalytic) were mixed and spray-coated onto the glass substrates as the control samples. Then the unrecoverable change of trimethoxy(alkyl)silane under UV illumination can be confirmed. It was found that the presence of trimethoxy(alkyl)silane in the TiO2–trimethoxy(alkyl)silane coating served to speed up the super-wettability transition time from superhydrophobicity to superhydrophilicity, but also limited the number of wettability recycle times. With this understanding, the effect of the trimethoxy(alkyl)silane concentration on the number of recycle cycles was investigated.

The separation of oil−water emulsion using superliquiphobic/philic porous coated materials has attracted considerable attention for dealing with environmental pollution and resource recycling issues. The coatings used may lack adequate surface mechanical and chemical durability. This paper proposes a simple method without other modifications for separating the oil−water emulsion. A porous layer was fabricated by superhydrophilic Al 2 O 3 particles, which could separate oil−water emulsions. The particle layer has the property of underwater superoleophobicity after prewetting. For the oil-in-water (O/W) emulsion separation, a 0.3 μm Al 2 O 3 particle layer was used. This layer had a pore size less than about 1 μm to minimize oil flow and to obtain a purity of oil recovery greater than 99 wt %. For the water-in-oil (W/O) emulsion separation, a 40 μm Al 2 O 3 superhydrophilic particle layer was used. Larger particles were used to provide a more porous surface to facilitate oil flow through the layer, resulting in a purity of water recovery purity greater than 99 wt %.