The demand for engineered wood products (EWPs) continues to rise internationally. However, for some important Australian commercial timbers such as plantation grown southern pine and native forest sourced spotted gum, a major impediment to achieving commercially viable EWP production is difficulties experienced in gluing – particularly for sawn laminate based EWPs such as glulam. Wettability and permeability have a major influence on wood adhesion. This study investigated the efficacy of different surface machining preparations on the wettability and permeability of southern pine and spotted gum. For both species, planing resulted in poor wettability, whereas face milling and sanding treatments post-planing improved wettability. Wettability increased in southern pine earlywood compared to latewood; and wettability decreased for both species with increased time post-surface machining. Planing resulted in the highest permeability for southern pine but the lowest permeability for spotted gum. Face milling resulted in higher permeability compared to sanding treatments.

Southern pine and spotted gum are two of Australia’s most important locally produced commercial timbers. However, internationally, they are amongst the most problematic species to glue cost-effectively, especially for sawn-laminate-based structural engineered wood products, such as glulam and cross-laminated timber. This study investigated the efficacy of different pre-gluing wood surface machining preparations on the tensile shear strength of lap shear samples prepared from both species. Surface machining methods tested included planing, face milling, and sanding post-planing with 40 and 80 grit sandpaper. Wood face milling is not currently used commercially in Australia and has not previously been adequately tested on Australian commercial timbers to improve wood adhesion. Planing is currently the most common method used internationally for preparing wood surfaces for gluing. For both species, face milling with fast feed speed (45 m/min), slow cutter speed (57 m/s), and sanding treatments post-planing resulted in significantly higher tensile shear strength compared to planing for lap shear samples that had been subjected to an accelerated weathering process. Performance differences in tensile shear strength between surface machining methods are likely to be related to the effects of these machining methods on surface roughness, fibrillation, and sub-surface cell damage.

The successful manufacturing of glulam from several important Australian commercial timbers is quite challenging due to difficulties in gluing. Improvements in adhesive bond performance of spotted gum, Darwin stringybark, and southern pine timber have been achieved using alternative pre-gluing surface machining methods, e.g., face milling and sanding-post planing, when compared to conventional planing methods. In order to improve the understanding of the effects that different surface machining methods have on adhesive bond performance, this study used micro X-ray computed tomography and microscopy to assess key adhesive bond criteria. There was a considerable loss in the amount of adhesive after the wet and dry test cycles for all species. There was also an extremely high frequency of voids in the glue lines for all species, which would negatively impact bond strength and durability. Face mill prepared timber boards resulted in thicker glue lines and greater resistance to adhesion loss, compared to boards prepared via planing. For the two hardwood species, face milling also resulted in greater adhesive penetration; however, for southern pine, there were no significant differences in adhesive penetration between the three surface machining treatments. Adhesive penetration was much deeper in southern pine compared to spotted gum and Darwin stringybark.

No abstract

Darwin stringybark (Eucalyptus tetrodonta) is one of Northern Australia’s most important commercial forest resources. The wood exhibits desirable wood properties including high strength, natural durability, and visual appeal. The production of engineered wood products (EWPs) such as glulam from this resource represents a significant commercial opportunity for the timber industry in northern Australia. However, a major challenge to overcome is the achievement of satisfactory glue bond performance. This study evaluated the effects of different surface machining preparations, adhesive types, and curing temperatures on the bonding characteristics of Darwin stringybark. The pre-gluing surface machining method significantly influenced the timber wettability, roughness, permeability and tensile shear strength of adhesive bonds. Planing resulted in the lowest wettability, roughness, and permeability, while bonded planed samples produced the poorest tensile shear strength. Alternative surface machining methods including face milling and sanding post-planing were shown to significantly improve the timber wettability, roughness, and permeability, and also to increase the tensile shear strength of bonded samples. The resorcinol formaldehyde adhesive resulted in slightly improved tensile shear strength in most cases compared to the polyurethane adhesive. There was no significant improvement in tensile shear strength with the use of elevated temperature curing.