In this paper, a full-scale model of Low Vibration Track was established and three working conditions were applied to a single bearing block; these include: vertical load at the end of the track slab, combination of horizontal and vertical load at the end of the track slab, and vertical load at the middle of the track slab. By applying four times static wheel load to the full-scale model, the relationship between the stress of the track structure and the load under different working conditions was investigated. The corresponding load values were obtained when the track slab and the bearing block reached the axial tensile strength of the concrete. Through the static load test, the weak position of the track structure was found, and the development trend of the crack was obtained. (1) Obtained the maximum stress of the concrete of the track slab at the corner of the bearing block, the maximal stress of the concrete of the track slab, the stress at the bottom of the bearing block, and the stress at the bottom of the bearing block under different working conditions. (2) The horizontal load of the train increased the force of the track slab concrete at the corners of the bearing block. (3) Compared the strain of different location of the track slab and different working conditions. (4) Observed the positions of slight crack and its development trend appeared on track slabs in different working conditions. (5) For the weak part of the track structure, it can be improved by measures such as increasing the thickness of the end of the track slab and arranging stirrups in the track slab around the support block. The research results provide reference for the design, application and maintenance of Low Vibration Track in the heavy-haul railway tunnel.

The train sometimes needs to brake frequently on the turnout, although the braking force does not exceed the limit resistance of fastener, cumulative displacement of rail occurs because of the long-term effect of the train brakes, thus, the relationship between the cumulative displacement of rail and the number of train braking actions should be explored. Aiming at the spring bar type III fastener, a 1:1 physical indoor simulation test was carried out, and an electromagnetic relay device was used to simulate the train load, force, and displacement sensors for data collection. Then a single load no more than the maximum resistance of fastener was applied to the rail end to explore the relationship between the number of loads and the rail cumulative deformation. The rail longitudinal cumulative displacement changes linearly in positive correlation with the number of load actions, and increases faster when the number of load actions is small. As the number of repeated loads increases, the above-mentioned relationship approximately and credibly obeys the power function distribution. Repeatedly applying load no more than the maximum longitudinal resistance of fastener to the rail, the existence of the rail cumulative displacement caused by frequent train braking can be demonstrated, and the relationship curve between the rail displacement and the number of loads can be obtained. Applying the fitting formula, the rail displacement after a specific number of loading times can be attained, and then referring to specific codes, we can determine whether it will exceed the safety limit.

With the gradual increase of the cargo weight of heavy-haul trains, the traditional ballasted track with the accumulation of stone and ballast has been unable to meet its structural safety requirements. From the comparison of the three common ballastless tracks in China, it can be seen that the low-vibration track (LVT) has the advantages of reasonable structure, low cost, and easy maintenance. Therefore, the design and research of heavy-haul railways are focused on, and it is urgent to study the applicability of LVT in heavy-haul railways. Method: By improving the slope of the short side of the LVT support block, the support block has a better load bearing capacity, so as to achieve the purpose of bearing a larger axle load. Through 1:1 full-scale model test and finite element simulation, the static mechanical properties of Improved LVT (ILVT) and Traditional LVT (TLVT) are compared and analyzed. Result: Compared with TLVT, ILVT has smaller vertical displacement and track gauge changes when subjected to the same load. The proven and reliable finite element model also shows that ILVT’s load sharing is less affected. In the case of achieving the same deformation, ILVT can withstand greater vertical and lateral loads. Conclusions: Compared with the TLVT, the ILVT design can reduce the vertical displacement of the rail and the supporting block, better control the track subsidence, and improve the driving safety of the LVT. At the same time, ILVT improves the anti-overturning ability of the rail and support block under lateral load, reduces the expansion of the gauge and the lateral spacing of the support block, and improves the stability of the track structure. ILVT can also be considered for the weight of 40t and other large axle load, and has broad application prospects.

Rigid body with initial velocity and no gravity contact with the elastomer, this process is too short and it can be described by collision. The geometry shape of contact surface is same as the contour of rigid body. Under the excitation of initial velocity, the particles of the contact surface produce motion and propagate around as the stress wave. The moving energy of rigid body is gradually consumed under the action of surface reaction force and goes through the deceleration stage. During the collision process, there is a continuous symmetrical stress pulse at the contact surface. This paper first discusses the interfacial stress pulse characteristics of infinite cylindrical side and elastomer under the condition of initial velocity and no gravity. And then the formation process of surface and surface particle stress pulse, the law of collision time and contact surface width are analyzed. This research is useful for the study of interfacial stress in finite boundary collision.

In this paper, relying on the National Engineering Laboratory of High-Speed Railway Construction Technology, a full-scale model of the double-block ballastless track structure is established, and the strain analysis of the layered track structure under different static loads is carried out, which has a certain practical significance for the design and maintenance of the high-speed railway ballastless track in our country. Research conclusion: (1) Under the action of static load, the sleeper directly under the rail is under compression; the four corners of the sleeper are tensile strain; (2) The strain at each measuring point on the surface of the track slab around the sleeper is compressive strain; the edge of the top surface of the track slab is compressive strain; The longitudinal strain at the bottom of the side of the track slab is tensile strain; (3) Under static load, the longitudinal strain measurement point on the top surface of the base plate is tensile strain at a distance of two sleepers from the static load position; the longitudinal strain at the bottom of the side of the base plate is tensile strain.