Purpose The purpose of this paper is to demonstrate the impact of the welding sequence on the substrate plate distortion during the wire and arc additive manufacturing (WAAM) process. This paper also aims to show the capability of finite element simulations in the prediction of those thermally induced distortions. Design/methodology/approach An experiment was conducted in which solid aluminum blocks were manufactured using two different welding sequences. The distortion of the substrates was measured at predefined positions and converted into bending and torsion values. Subsequently, a weakly coupled thermo-mechanical finite element model was created using the Abaqus simulation software. The model was calibrated and validated with data gathered from the experiments. Findings The results of this paper showed that the welding sequence of a part significantly affects the formation of thermally induced distortions of the final part. The calibrated simulation model was able to capture the different distortion behavior attributed to the welding sequences. Originality/value Within this work, a simulation model was developed capable of predicting the distortion of WAAM parts in advance. The findings of this paper can be used to improve the design of WAAM welding sequences while avoiding high experimental efforts.

Coaxial laser metal deposition with wire (LMD-w) is an innovative additive manufacturing technology in which a wire is coaxially fed through the center of a hollow laser beam into a laser-induced melt pool. This special configuration results in a direction-independent process, which facilitates the manufacturing of thin-walled metal components at high deposition rates. However, laborious experimental test series must be conducted to adjust the process parameters so that the substrate and the part do not overheat. Therefore, models are needed to predict the resulting temperature field and melt pool dimensions efficiently. This paper proposes a finite element simulation model using an innovative heat source, which considers the unique intensity distribution of the annular laser spot. The heat source parameters were calibrated experimentally based on fusion lines obtained from metallographic cross sections of aluminum alloy samples (AA5078 wire and AA6082 substrate). Subsequently, the temperature distribution in the substrate plate was measured by means of thermocouples to validate the developed model. It was shown that the proposed heat source replicates the heat input accurately. With the presented model, essential features for process development, such as the temperature field and the melt pool dimensions, can be reliably predicted. The model contributes to a better understanding of the LMD-w process and facilitates an efficient process development in future research work as well as for industrial applications. Key words: thermal simulation, annular laser spot, heat source, laser metal deposition, coaxial wire feeding, directed energy deposition

Laser metal deposition with coaxial wire feeding is a directed energy deposition process in which a metal wire is fed to a laser-induced melt pool. Oxidation occurring during the process is a major challenge as it significantly influences the mechanical properties of the produced part. Therefore, an inert gas atmosphere is required in the high temperature process zone, whereby local shielding offers significant cost advantages over an inert gas chamber. In this work, a novel local shielding gas nozzle was developed based on basic methods of fluid mechanics. A gas flow-optimized prototype incorporating internal cooling channels was additively manufactured by laser-powder bed fusion and tested for its effectiveness via deposition experiments. Using the developed local shielding gas concept, an unwanted mixing with the atmosphere due to turbulence was avoided and an oxide-free deposition was achieved when processing a stainless steel ER316LSi wire. Furthermore, the effects of the shielding gas flow rate were investigated, where a negative correlation with the melt pool temperature as well as the weld bead width was demonstrated. Finally, a solid cuboid was successfully built up without oxide inclusions. Overheating of the nozzle due to reflected laser radiation could be avoided by the internal cooling system. The concept, which can be applied to most commercially available coaxial wire deposition heads, represents an important step for the economical application of laser metal deposition.

Wire arc additive manufacturing (WAAM) is an additive manufacturing process based on gas metal arc welding. It allows the fabrication of large-volume metal components by the controlled deposition and stacking of weld beads. Next to the near-net-shape manufacturing of metal components, WAAM is also applied in the local reinforcement of structural parts, such as shell geometries. However, this procedure can lead to undesired thermally induced distortions. In this work, the distortion caused by the WAAM reinforcement of half-cylinder shell geometries was investigated through experiments and transient thermo-mechanical finite element simulations. In the experiments, the weld beads were applied to the specimen, while its thermal history was measured using thermocouples. The developing distortions were registered using displacement transducers. The experimental data were used to calibrate and validate the simulation. Using the validated model, the temperature field and the distortions of the specimens could be predicted. Subsequently, the simulation was used to assess different deposition patterns and shell thicknesses with regard to the resulting part distortions. The investigations revealed a non-linear relation between shell thickness and distortion. Moreover, the orientation and the sequence of the weld beads had a significant impact on the formation of distortion. However, those effects diminished with an increasing shell thickness.