The present work reports a systematic study on the structural, thermal, electrical and electrochemical stability of SrCo1−xNbxO2.5+δ series as a potential reversible oxygen-electrode for intermediate-temperature solid oxide fuel cells. The identified best composition is x = 0.10, which exhibits a stable pseudo primitive cubic structure at <700°C and a reversible oxygen redox reaction at 350°C. The conductivity of this material is p-type and also exhibits a peak at 350°C, implying that the electron hole conduction is closely associated with the oxygen nonstoichiometry. Electrochemical impedance spectroscopy analysis indicates a low polarization resistance rate-limited by a slower surface O2 dissociation step. Overall, the material is thermally stable and oxygen redox reversible below 700°C, above which a catalytically less active brownmillerite SrCoO2.5 is formed.

The present study reports thermal and electrical properties of Sr 1-x Y x CoO 2.5+δ (x = 0-0.40) as a promising cathode for intermediatetemperature solid oxide fuel cells. The results show that x = 0.10 is the best composition possessing a single primitive cubic perovskite structure, stable conductivity and the lowest polarization resistance. Thermogravimetric analysis indicates an oxygen intake from RT to ∼375 • C, above which oxygen loss occurs. The oxygen gain-loss behavior corresponds well with the conductivity increase-decrease trending, reflecting that oxygen-nonstoichiometry controls the hole-concentration (or oxidation-state of Co-ions). Electrochemical impedance spectroscopy analysis further reveals that the overall ORR polarization consists of a faster charge-transfer and a slower surface oxygen exchange.

In the present study, electrical properties of a composite electrolyte composed of a BaZr 0.8 Y 0.2 O 3-δ (BZY) and a perspective of defect chemistry. A DFT first-principles calculation further confirmed that proton transfer in molten carbonates was a low-energy process.

No abstract

1. Introduction High temperature (HT) operation at 800 – 1000 °C causes many problems such as the thermal mismatch between membrane electrode assembly (MEA) components, expensive bipolar plates, micro structural changes, inter-diffusions, slow start-up time, decreasing system power density due to heat insulators. In order to overcome this main commercialization obstacle of solid oxide fuel cells (SOFCs), a lot of intermediate temperature (IT) electrolyte materials (Doped ceria, LSGM, ScSZ and so on) which can substitute for conventional YSZ have been proposed. And various thin film deposition techniques (Screen printing, Dip-coating, Magnetron sputtering, Pulsed Laser Deposition, Chemical Vapor Deposition and Atomic Layer Deposition) were applied to this research field. The goal of both types of approaches is minimizing the ionic resistance at decreased temperature. Recently, the sodium doped strontium silicate (Sr1-xNaxSiO3-0.5x) is gathering attentions as a fast ion conductor.[1] And Wei et al. confirmed a good SOFC performance using this electrolyte material at 500 and 600 °C. [2] In this study, we investigated on this promising material to get the optimal fabrication conditions with composition and to minimize several problems on this material. 2. Experimental The starting raw powders of SrCO3 (Sigma-Aldrich 99.9%), Na2CO3 (Alfa Aesar, 99.9%) and SiO2(Alfa Aesar 99.9%) were mixed and ball milled. The Na doping percentages on strontium site were 0 to 100 %. We varied calcination temperature from 600 °C to 1000 °C. After ball milling step, we also varied sintering temperature (800 – 1150 °C) and time (10, 20 and 100 h).  Conductivity tests were conducted in the air environment and the furnace was controlled from 400 to 750 °C. Sample pellet was prepared to get the thickness of 1.5 mm using low speed saw. Then, we pasted silver electrodes with current collecting meshes on both sides of  pellets and connected wires to electrochemical impedance spectrometer (Solartron 1287 and 1260, UK). The micro structural images were captured using a field emission scanning electron microscope (FESEM, Zeiss Ultra) equipped with an energy dispersive X-ray spectroscopy (EDS) analyzer, respectively. The phase check was done using an X-ray diffractometer (D/max-A, Rigaku, Japan) with CuKα radiation (λ=1.5418 Å). The scan range was 2θ = 10 – 70 °at a rate of 5 ° min-1. From this study, we found out the optimal fabrication conditions (sintering at 900 °C for 10 h) for 45 % sodium doped strontium silicate electrolyte which was known as the best ionic conductor. Moreover, we could guess the origin of this high conductivity was from the amorphous sodium silicate. Reference [1] P. Singh and J. B. Goodenough, J. Am. Chem. Soc., 2013, 135, 10149–10154 [2] T. Wei, P.Singh, Y. Gong, J.B. Goodenough, Y. Huang and K. Huang, Energy Environ. Sci., 2014, 7, 1680-1684 Figure 1