With the breadth of applications and analysis performed over the last few decades, it would not be an exaggeration to call piezoelectric materials “the top of the crop” of smart materials. Piezoelectric materials have emerged as the most researched materials for practical applications among the numerous smart materials. They owe it to a few main reasons, including low cost, high bandwidth of service, availability in a variety of formats, and ease of handling and execution. Several authors have used piezoelectric materials as sensors and actuators to effectively control structural vibrations, noise, and active control, as well as for structural health monitoring, over the last three decades. These studies cover a wide range of engineering disciplines, from vast space systems to aerospace, automotive, civil, and biomedical engineering. Therefore, in this review, a study has been reported on piezoelectric materials and their advantages in engineering fields with fundamental modeling and applications. Next, the new approaches and hypotheses suggested by different scholars are also explored for control/repair methods and the structural health monitoring of engineering structures. Lastly, the challenges and opportunities has been discussed based on the exhaustive literature studies for future work. As a result, this review can serve as a guideline for the researchers who want to use piezoelectric materials for engineering structures.

In the last three decades, smart materials have become popular. The piezoelectric materials have shown key characteristics for engineering applications, such as in sensors and actuators for industrial use. Because of their excellent mechanical-to-electrical and vice versa energy conversion properties, piezoelectric materials with high piezoelectric charge and voltage coefficient have been tested in renewable energy applications. The fundamental component of the energy harvester is the piezoelectric material, which, when subjected to mechanical vibrations or applied stress, induces the displaced ions in the material and results in a net electric charge due to the dipole moment of the unit cell. This phenomenon builds an electric potential across the material. In this review article, a detailed study focused on the piezoelectric energy harvesters (PEH’s) is reported. In addition, the fundamental idea about piezoelectric materials, along with their modeling for various applications, are detailed systematically. Then a summary of previous studies based on PEH’s other applications is listed, considering the technical aspects and methodologies. A discussion has been provided as a critical review of current challenges in this field. As a result, this review can provide a guideline for the scholars who want to use PEH’s for their research.

The use of date palm fiber (DPF) as natural fiber in concrete and mortar continues to gain acceptability due to its low-cost and availability. However, the main disadvantage of DPF in cement-based composites is that it reduces compressive strength and increases the porosity of the composite. Hence, for DPF to be efficiently used in concrete, its negative effects must be counteracted. Therefore, in this study, silica fume was employed as supplementary cementitious material to alleviate the negative effects of DPF on the strength and porosity of concrete. The DPF was added in different dosages of 0%, 1%, 2%, and 3% by weight of binder materials. Silica fume was used as a cement replacement material at dosages of 0% to 15% (intervals of 5%) by volume of cement. The unit weights, mechanical strengths, water absorption, and microstructural morphology were all evaluated. The concrete’s fresh and hardened densities were reduced with the increment in DPF and silica fume. The compressive strength declined at all ages with the increment in DPF addition, while the flexural and splitting tensile strengths improved with addition of up to 2% DPF. Furthermore, the concrete’s water absorption escalated with an increase in DPF content. Silica fume significantly enhanced the mechanical strength of the concrete. The dissipation in compressive strength with the addition of up to 2% DPF was mitigated by replacing up to 10% cement with silica fume, where it densified the microstructure and refined the interfacial transition zone between the fibers and cement matrix, hence significantly decreasing the porosity and enhancing durability.

Waste tire disposal continues to pose a threat to the environment due to its non-biodegradable nature. Therefore, some means of managing waste tires include grinding them to crumb rubber (CR) sizes and using them as a partial replacement to fine aggregate in concrete. However, the use of CR has a series of advantages, but its major disadvantage is strength reduction. This leads to the utilization of calcium carbide waste (CCW) to mitigate the negative effect of CR in self-compacting concrete (SCC). This study investigates the durability properties of SCC containing CR modified using fly ash and CCW. The durability properties considered are water absorption, acid attack, salt resistance, and elevated temperature of the mixes. The experiment was conducted for mixes with no-fly ash content and their replica mixes containing fly ash to replace 40% of the cement. In the mixes, CR was used to partially replace fine aggregate in proportions of 0%, 10%, and 20% by volume, and CCW was used as a partial replacement to cement at 0%, 5%, and 10% by volume. The results indicate that the mixes containing fly ash had higher resistance to acid (H2SO4) and salt (MgSO4), with up to 23% resistance observed when compared to the mix containing no fly ash. In addition, resistance to acid attack decreased with the increase in the replacement of fine aggregate with CR. The same principle applied to the salt attack scenario, although the rate was more rapid with the acid than the salt. The results obtained from heating indicate that the weight loss was reduced slightly with the increase in CCW, and was increased with the increase in CR and temperature. Similarly, the compressive strength was observed to slightly increase at room temperature (27 °C) and the greatest loss in compressive strength was observed between the temperature of 300 and 400 °C. However, highest water absorption, of 2.83%, was observed in the mix containing 20% CR, and 0% CCW, while the lowest water absorption, of 1.68%, was found in the mix with 0% CR, 40% fly ash, and 10% CCW. In conclusion, fly ash is recommended for concrete structures immersed in water, acid, or salt in sulphate- and magnesium-prone areas; conversely, fly ash and CR reduce the resistance of SCC to heat beyond 200 °C.

In structural engineering, thin-walled structures play an important role in the design of the lightweight structural model. It carries different loading conditions when it exists in any model, and it is designed with thin plates or thin shells. Penetrating thin-walled structures with different kinds of holes can decrease their weight and facilitate repair and maintenance operations, such as those carried out for the wing of an airplane. In such applications, cutouts are often employed as part of the design of composite plates. Therefore, this paper attempted to design and analyse the thin-walled composite structure with a C-cross-section shape. To model and analyse the structures, a finite element method was utilized using the ABAQUS commercial tool, and the results of critical buckling load for different laminate types were obtained. Composite materials and structures have different parameters that can vary the results of analysis; therefore, to optimize the current mode a design of experiments method is used via MINITAB 20 and Design-Expert 13 tools. The selected parameters for this work were the opening ratio, spacing ratio, and shape of the hole for the output response as a critical buckling load was carried out. Based on the current results of simulation and optimization, it was found that the parameters of composite materials and structures will impact the output response, and the current study investigated the optimum parameters for the best possible outcome of the structural analysis.