The high quality properties and benefits of graphene-oxide have generated an active area of research where many investigations have shown potential applications in various technological fields. This paper proposes a methodology for enhancing the pyro-electricity of PVDF by graphene-oxide doping. The PVDF film with graphene-oxide is prepared by the sol-gel method. Firstly, PVDF and graphene-oxide powders are dispersed into dimethylformamide as solvent to form a sol solution. Secondly, the sol solution is deposited on a flexible ITO/PET substrate by spin-coating. Thirdly, the particles in the sol solution are polymerized through baking off the solvent to produce a gel in a state of a continuous network of PVDF and graphene-oxide. The final annealing process pyrolyzes the gel and form a β-phase PVDF film with graphene-oxide doping. A complete study on the process of the graphene oxide doping of PVDF is accomplished. Some key points about the process are addressed based on experiments. The solutions to some key issues are found in this work, such as the porosity of film, the annealing temperature limitation by the use of flexible PET substrate, and the concentrations of PVDF and graphene-oxide.

Micromixers are the devices which have the ability to mix liquids uniformly. However, a Tesla valve has the potential for micromixer development because of its simple structure and special flow mechanism. In this study, a numerical simulation analysis of a new Tesla-type micromixer was designed by placing a flow plate into a micromixer, which has a contact angle of 30° with the channel wall. The optimization of the geometric parameter, aspect ratio (AR) and the Reynolds number (Re) effect is discussed. The results show that the optimal geometric parameters of the unit Tesla-type micromixer are θ1 = 45°, θ2 = 30°, A = 0.3 mm, B = 0.22 mm, C = 0.3 mm, D = 0.25 mm, and the mixing efficiency can achieve εmixing = 0.953 by passing three-unit Tesla-type micromixers (inverse-type, Re = 1, AR = 1). The Tesla-type micromixers designed in this study, which have a lower pressure drop and a higher mixing performance at a low Reynolds number, can contribute to the application of biomedical chips and chemical reactors.

Movable suspended microstructures are the common feature of sensors or devices in the fields of Complementary-Metal-Oxide-Semiconductors and Micro-Electro-Mechanical Systems which are usually abbreviated as CMOS-MEMS. To suspend the microstructures, it is commonly to etch the sacrificial layer under the microstructure layer. For large-area microstructures, it is necessary to design a large number of etching holes on the microstructure to enhance the etchant uniformly and rapidly permeate into the sacrificial layer. This paper aims at evaluating the fringe capacitance caused by etching holes on microstructures and developing empirical formulas. The formula of capacitance compensation term is derived by curve-fitting on the simulation results by the commercial software ANSYS. Compared with the ANSYS simulation, the deviation of the present formula is within˘5%. The application to determine the capacitance of an electrostatic micro-beam with etching holes is demonstrated in a microstructure experiment, which agrees very well with the experimental data, and the maximum deviation is within˘8%. The present formula is with simple form, wide application range, high accuracy, and easy to use. It is expected to provide the micro-device designers to estimate the capacitance of microstructures with etching holes and predominate in the device characteristics.

The electro-Fenton system has the ability to degrade wastewater and has received attention from many researchers. Currently, the core development objective is to effectively increase the degraded wastewater decolorization efficiency in the system. In this study, to improve the electro-Fenton system reaction rate and overall electrical properties, we used polyvinylidene difluoride to fix carbon nanotubes (CNTs) and graphene onto the system cathode (carbon felt electrode), which was then used to process Reactive Black 5 wastewater. Furthermore, we (1) used scanning electron microscopy to observe the structural changes in the electrode surface after modification; (2) used the Tafel curve to determine the electrode corrosion voltage and corrosion rate; and (3) analyzed the azo-dye decolorization level. The results showed that the maximum system decolorization rates of the CNT- and graphene-modified carbon felt electrodes were 55.3% and 70.1%, respectively. These rates were, respectively, 1.2 and 1.5 times higher than that of the unmodified carbon felt electrode, implying that we successfully improved the cathode characteristics. The modified electrode exhibited an improved conductivity and corrosion resistance, which, in turn, improved the system decolorization efficiency. This significantly increased the electro-Fenton system overall efficacy, making it valuable for future applications.

Bio-electro-Fenton microbial fuel cells generate energy through the decomposition of organic matter by microorganisms. The generated electricity drives a Fenton reaction in a cathode chamber, which can be used for the decolorization of dye wastewater. Most of the previous works added expensive platinum catalyst to improve the electrical property of the system. In this research, aligned carbon nanotubes (CNTs) were generated on the surface of SS316 stainless steel by chemical vapor deposition, and an iron phthalocyanine (FePc) catalyst was added to fabricate a compound (FePc/CNT/SS316) that was applied to the cathode electrode of the fuel cell system. This was expected to improve the overall electricity generation efficiency and extent of decolorization of the system. The results showed that the maximum current density of the system with the modified electrode was 3206.30 mA/m2, and the maximum power was 726.55 mW/m2, which were increased by 937 and 2594 times, respectively, compared to the current and power densities of a system where only the SS316 stainless steel electrode was used. In addition, the decolorization of RB5 dye reached 84.6% within 12 h. Measurements of the electrical properties of bio-electro-Fenton microbial fuel cells and dye decolorization experiments with the FePc/CNT/SS316 electrode showed good results.