To investigate the deformation and damage characteristics of internal coal bodies of small pillars under different pressures, rock–coal–rock assemblage samples were subjected to the conventional triaxial compression test to analyze the mechanical behavior characteristics under different pressures. The results showed that, with the increase in peripheral pressure, the peak strength and modulus of elasticity of the assemblage specimens increased, the range of fracture compaction stage gradually decreased, and the specimen was gradually transformed from brittle to ductile. With an increase in peripheral pressure, the residual strength gradually increased, and the strength decay coefficient gradually decreased. The strength decay coefficient decreased the most at 0–10 MPa, and this decrease slowed down after exceeding 15 MPa. When the peripheral pressure was 0 MPa, the damage degree of the coal pillar was larger. With the increase in peripheral pressure, the number of cracks in the coal column increased, the damage degree increased more, and mixed damage characteristics of tension–shear were found. Based on the Hoek–Brown criterion, the strength criterion applicable to the specimen of rock–coal–rock combination was obtained through numerical fitting iteration, which provides an experimental and theoretical basis for realizing the stability control of small coal columns.

Surrounding rock of roadway with a coal–rock interface is a common form in coal mines. In order to determine deformation characteristics and obtain the control principle of roadways with a coal–rock interface, the interface between the roof and coal seam was added to simulate the weak cohesion between the stratum. In this model, the interface shear stiffness was considered to be one of the key factors affecting horizontal inward movement of the roadway sidewalls. The deformation of the roadway with or without coal–rock interface under different burial depths was analyzed. Then, the shear stiffness of the interface element was changed to study the influence of shear stiffness on roadway deformation. At the same time, the characteristics of discontinuous deformation caused by the coal–rock interface at different positions in the roadway were studied. The results show that the roadway sidewall appeared to bulge in the middle and there is no dislocation and a small deformation in the contact position of the roadway sidewall with the roof and the floor when there is no interface between the stratum of the roadway. When there is an interface, the sidewall of the roadway is extruded as a whole, the slip and dislocation between the coal sidewall and the roof were obvious, and the maximum deformation of the sidewall is 1.68 times that of the roadway without an interface. When the shear stiffness of the interface is low, the deformation and the range of the plastic zone of roadway are large, with a large deformation at the upper part of the roadway sidewall, and a small deformation at the lower part of the roadway sidewall. The deformation of sidewall at the interface position decreases gradually with the increase of the interface shear stiffness, approaching the shape without the interface. When the coal–rock interface is at the sidewall of the roadway, the deformation of the rock and coal body at the interface is discontinuous, with slip and dislocation. The greater the proportion of rock height in the roadway sidewall, the greater the rock deformation. On the contrary, the coal deformation increases. It is more reasonable to simulate the deformation of roadways by adding a coal–rock interface, and the results are closer to the actual situation.

The stability control of surrounding rock in deep roadway is becoming more and more difficult, and grouting reinforcement support has become the mainstream of roadway control. In order to obtain the ratio of quasi-sandstone material corresponding to the grouting body, this paper uses river sand as aggregate, cement and gypsum as cementing agent, retarder and defoamer as additives, and carries out orthogonal proportioning tests with three influencing factors: water-binder ratio (ratio of water to mass of cementing agent), gypsum-cement ratio (ratio of gypsum to mass of cement) and binder-aggregate ratio (ratio of cementing agent to aggregate mass), and compares and analyzes the sensitivity of each factor on the density, compressive strength, tensile strength, elastic modulus, Poisson’s ratio, longitudinal wave velocity, elasticity index and brittleness index of quasi-sandstone material. The results show that 1) the Water-binder ratio has the greatest effect on the sensitivity of material compressive strength, tensile strength, elastic modulus, Poisson’s ratio and longitudinal wave velocity; the gypsum-cement ratio has the greatest effect on the sensitivity of material deformation index and brittleness index; the binder-aggregate ratio has the greatest effect on the sensitivity of material density. 2) Reducing the Water-binder ratio can improve the density, compressive strength and tensile strength of the material; reducing the paste ratio can improve the modulus of elasticity, Poisson’s ratio and longitudinal wave speed of the material; as the gypsum-cement ratio increases, the deformation index first decreases and then increases and then decreases; as the binder-aggregate ratio increases, the brittleness index first increases and then decreases and then increases. 3) The empirical equations between physical and mechanical properties of sandstone-like materials and Water-binder ratio, gypsum-cement ratio and binder-aggregate ratio were established based on multiple linear regression analysis, and more reasonable material ratios were quickly obtained by physical and mechanical parameters of materials. The results of the study provide theoretical references for similar material simulation tests for quasi-sandstone grouting.