No abstract

One of the concerned technical issues in the nuclear piping under operation is pipe wall thinning caused by flow accelerated corrosion. Recently, it has been reported that the elbow section is more suspicious on pipe wall thinning by erosion–corrosion. Some researchers including authors have been studied static and fatigue strength of elbows with local wall thinning. However, still more experiment and analysis data are needed to clarify the technical issues. Accordingly, further experiments and their evaluations were carried out by the authors. This paper presents the influences of size and location on fatigue life. Also as one of the application of the test results, safety margin of elbows with wall thinning against seismic loading is discussed. Low cycle fatigue tests were conducted using elbow specimens made of STPT410 steel with local wall thinning. The local wall thinning was machined on the inside of elbow specimens in order to simulate erosion/corrosion metal loss. The local wall thinning areas were located at three different areas, called extrados, crown, and intrados. Eroded ratio (eroded depth/wall thickness) is 0.5 and 0.8 and eroded angle is 90 deg and 180 deg. The elbow specimens were subjected to cyclic in-plane bending under displacement control (±20 mm) without and with internal pressure of 3 MPa using a universal testing machine. Fatigue life was defined as fatigue crack penetration through the thickness and crack penetration was watched by naked eyes during the test through the protection window made of a transparent plastic plate. Obtained main conclusions are as follows: (1) Existence of local wall thinning in extrados does not have an important effect on fatigue life. Especially, fatigue crack does not initiate at the extrados where the extreme local wall thinning exists (eroded ratio = 0.8 and eroded angle = 180 deg). (2) Regardless of existence of internal pressure, fatigue crack initiates at the crown where local wall thinning does not exist for an elbow with local wall thinning at extrados. This conclusion should be confirmed using eroded elbow specimens under more high pressure. (3) Even if the eroded ratio and the eroded angle reached up to 0.8 and 180 deg, the elbows with local wall thinning have high safety margin against seismic loading, comparing to ASME Boiler and Pressure Vessel Code Section 3 allowable seismic stress criteria.

The stress states of elbow pipes are complex and different from those of straight pipes. Manson's universal slope method cannot predict the low-cycle fatigue lives of elbow pipes under combined cyclic bending and internal pressure. In this work, fatigue tests and finite element analysis showed that the multi-axial stress factor (i.e., ratio of axial stress to hoop stress) is quite high at elbows. This paper proposes a revised Manson's universal slope method that considers the multi-axial stress factor to predict the low-cycle fatigue lives of elbows under combined cyclic bending and internal pressure with considerably high accuracy.

Elbow pipes are commonly used in the piping systems of power plants and chemical plants. The stress states at the elbow part are complex and quite different from those of the straight pipes. It is well known that the fatigue lives of metals under simple push-pull conditions can be successfully predicted by Manson’s universal slope method. However, the low-cycle fatigue lives of elbow pipes under combined cyclic bending and inner pressure cannot be predicted by this method, though the reasons for this have not been clarified. In this work, the low-cycle fatigue tests and finite element analysis of elbows under cyclic bending and inner pressures were carried out. The results showed that the multi-axial stress factor, which is a ratio of hoop stress and axial stress, at elbows is quite high. Considering the multi-axial stress factor, a revised Manson’s universal slope method is proposed in this paper. Using the proposed method, we were able to predict conservatively the low-cycle fatigue lives of elbows under combined cyclic bending and inner pressure.

One of the concerned technical issues in the nuclear piping under operation is pipe wall thinning caused by flow accelerated corrosion. This paper focuses on influence of internal pressure on low cycle fatigue life of pipe bends with local wall thinning and evaluation of safety margin against seismic loading in order to apply the obtained knowledge to the nuclear piping. In-plane bending fatigue tests under several constant internal pressure magnitudes were carried out using carbon steel pipe bends with local wall thinning at the extrados. Also finite element analysis, code-based seismic evaluation and fatigue analysis based on calculated strain range were carried out. Obtained main conclusions are as follows: (1) the tested pipe bends with local wall thinning at the extrados have a strong resistance against fatigue failure based on nuclear seismic piping design in Japan at least up to 12 MPa. That is, the tested pipe bends with severe local wall thinning (eroded ratio = 0.5 and eroded angle = 180 deg) at the extrados have margins against fatigue failure, even though the wall thickness is less than the code-required minimum value based on the nuclear piping seismic design in Japan. (2) Combination of the conventional B2 index and the Ke factor provided in the JSME Design and Construction Code, which is referred by JEAC 4601-2008 overestimates fictitious stress amplitude, when sum of the primary and secondary stress is much greater than 3 Sm.