No abstract

It is of critical importance to improve toughness, strength, and wear-resistance together for the development of advanced structural materials. Herein, we report on the synthesis of unoxidized graphene/alumina composite materials having enhanced toughness, strength, and wear-resistance by a low-cost and environmentally benign pressure-less-sintering process. The wear resistance of the composites was increased by one order of magnitude even under high normal load condition (25 N) as a result of a tribological effect of graphene along with enhanced fracture toughness (KIC) and flexural strength (σf) of the composites by ~75% (5.60 MPa·m1/2) and ~25% (430 MPa), respectively, compared with those of pure Al2O3. Furthermore, we found that only a small fraction of ultra-thin graphene (0.25–0.5 vol%, platelet thickness of 2–5 nm) was enough to reinforce the composite. In contrast to unoxidized graphene, graphene oxide (G-O) and reduced graphene oxide (rG-O) showed little or less enhancement of fracture toughness due to the degraded mechanical strength of rG-O and the structural defects of the G-O composites.

2 mol% Al-doped ZnO nanoparticles were consolidated into a ZnO nanocomposite with ZnAl 2 O 4 nanoprecipitates by spark plasma sintering and its high-temperature charge transport and thermoelectric properties were investigated up to 1073 K. The carrier concentration in the nanocomposite was not dependent on the temperature, while the Hall mobility showed positive temperature-dependence due to grain boundary scattering. The negative Seebeck coefficient of the nanocomposite was linearly proportional to the temperature, and the density of the state effective mass (m d *) was evaluated to be 0.33m e by using the Pisarenko relation. Drastic reduction of thermal conductivity (k < 2 W m À1 K À1 ) was achieved in the nanocomposite, and the maximum ZT of 0.34 was obtained at 1073 K.

In thermoelectric energy conversions, thermal conductivity reduction is essential for enhancing thermoelectric performance while maintaining a high power factor. Herein, we propose an approach based on coated-grain structures to effectively reduce the thermal conductivity to a much greater degree when compared to that done by conventional nanodot nanocomposite. By incorporating CdTe coated layers on the surface of SnTe grains, the thermal conductivity is as low as 1.16 W/m-K at 929 K, resulting in a thermoelectric figure of merit, i.e., zT, of 1.90. According to our developed theory, phonons scatter coherently due to the phase lag between phonons passing through and around the coated grain. Such scattering is induced by the acoustic impedance mismatch between the coated layer and the grain, resulting in a gigantic phonon-scattering cross section. The phonon-scattering cross section of the coated grains is several orders of magnitude larger than that of the nanodots with the same impurity concentration. The power factor was also slightly increased by the energy filtering effect at the coated surface and additional minority carrier blocking by the heterointerfaces. This scheme can be utilized for various bulk crystals, meaning a broad range of materials can be considered for thermoelectric applications.

The effects of feeding rate and feeding frequency on survival, growth and body composition of ayu post‐larvae (0.15 g in body weight and 3.5 cm in total length) were investigated in this study. A factorial experimental design of two feeding rates (3 and 6% of body weight of fish per meal) five feeding frequencies (one meal in 2 d, one meal a day, two meals a day, four meals a day, and six meals a day) with three replicates was used. Survival of ayu post‐larvae was significantly (P 0.05) affected by feeding frequency but not by feeding rate. Survival of ayu improved linearly with feeding frequency at both feeding rates. Weight and length gains and specific growth rate (SGR) of ayu was significantly (P 0.05) affected by feeding frequency but not by feeding rate, with weight and length gains and SGR linearly elevated with increasing feeding frequency at both feeding rates. The greatest weight and length gains were observed in fish receiving six meals daily at both feeding rates; however, no significant difference in weight gain was observed among two, four, and six meals a day, or in length gain between four and six meals a day. Feed efficiency ratio (FER) was significantly (P 0.05) affected by both feeding rate and feeding frequency. FER linearly decreased with feeding frequency at both feeding rates or feeding rate in the same feeding frequency. When the total daily amount of feed supply was constant with various feeding frequencies at different feeding rates (one meal a day at 3% feeding rate and one meal in 2 d at 6% feeding rate, two meals a day at 3% feeding rate and one meal a day at 6% feeding rate, or four meals a day at 3% feeding rate and two meals a day at 6% feeding rate), improvement in survival, weight and length gains, and SGR was observed in fish with higher feeding frequency at lower feeding rate. Moisture, protein, and lipid content of fish were not significantly (P > 0.05) affected by either feeding rate or feeding frequency. However, lipid content of ayu linearly increased with feeding frequency at 6% feeding rate. The highest body lipid content was observed in fish receiving six meals daily at both feeding rates. Ash content of fish was significantly (P 0.05) affected by feeding frequency but not by feeding rate. Based on performance of ayu, it can be concluded that optimum feeding rate and feeding frequency for ayu post‐larvae (an initial weight of 0.15 g) were 3% per meal and four meals a day, respectively, under these experimental conditions.