Using conventional high temperature superconducting wire, model Superconducting Fault Current Limiter (SFCL) is made and tested. Solenoid coil using Bi2223 silver sheath wire is so made that inductance is as small as possible and a vacuum interrupter is connected in series of it. In parallel of these, a conventional reactor coil is connected. When the fault current flows in this equipment, superconducting wire is quenched and current is transferred into the parallel coil because of voltage drop of superconducting wire. This large current in parallel coil actuates magnetic repulsion mechanism of vacuum interrupter. Due to opening of vacuum interrupter, the current in superconducting wire is broken. By using this equipment, current flow time in superconducting wire can be easily minimized. On the other hand, the fault current is also easily limited by large reactance of parallel coil.

SUMMARYUsing high-temperature superconductors, a superconducting fault current limiter (SFCL) was fabricated and tested. The superconductor and a vacuum interrupter serving as a commutation switch were connected in parallel with a bypass coil. When a fault occurs and excessive current flows, the superconductor is first quenched and the current is transferred to the bypass coil because of the voltage drop of the superconductor. At the same time, since a magnetic field is generated by the current flowing in the bypass coil, the commutation switch is immediately driven by an electromagnetic repulsion plate connected to the driving rod of the vacuum interrupter (VI), and the superconductor is separated from this circuit. Using the test model, we were able to separate the superconductor from the circuit by the movement of the VI within a half current cycle and to transfer all current to the bypass coil. Since the operation of the commutation switch is included in the current limiting operation of this test model, it will be a useful circuit in the development of SFCL in the future. Moreover, since it can make the energy consumption of the superconductor small during the fault state due to the realization of a high-speed switch with simple composition, the burden on the superconductor is reduced compared with the conventional resistive type of SFCL and it is considered that the flexibility of SFCL design is increased. Cooperation with a circuit breaker was also considered; trial calculations of the parameters and energy of operation were conducted and a discussion of the installation of the SFCL in an electric power system is presented.

SUMMARYUsing conventional high-temperature superconducting wire, a model superconducting fault current limiter (SFCL) is made and tested. Solenoid coil using Bi2223 silver sheath wire is so made that inductance is as small as possible and a vacuum interrupter is connected in series to it. A conventional reactor coil is connected in parallel. When the fault current flows in this equipment, superconducting wire is quenched and current is transferred into the parallel coil because of voltage drop of superconducting wire. This large current in parallel coil actuates magnetic repulsion mechanism of vacuum interrupter. Due to opening of vacuum interrupter, the current in superconducting wire is broken. By using this equipment, current flow time in superconducting wire can be easily minimized. On the other hand, the fault current is also easily limited by large reactance of parallel coil.

Using high temperature superconductor, a Superconducting Fault Current Limiter (SFCL) was made and tested. Superconductor and vacuum interrupter as commutation switch are connected in parallel with bypass coil. When a fault occurs and the excessive current flows, superconductor is first quenched and the current is transferred to bypass coil because on voltage drop of superconductor. At the same time, since magnetic field is generated by current which flows in bypass coil, commutation switch is immediately driven by electromagnetic repulsion plate connected to driving rod of vacuum interrupter, and superconductor is separated from this circuit. Using the testing model, we could separate the superconductor from a circuit due to movement of vacuum interrupter within half-cycle current and transfer all current to bypass coil. Since operation of a commutation switch is included in current limiting operation of this testing model, it is one of helpful circuit of development of SFCL in the future. Moreover, since it can make the consumed energy of superconductor small during fault state due to realization of high-speed switch with simple composition, the burden of superconductor is reduced compared with conventional resistive type SFCL and it is considered that the flexibility of a SFCL design increases. Cooperation with a circuit breaker was also considered, the trial calculation of a parameter and energy of operation is conducted and discussion in the case of installing the SFCL to electric power system is made.

No abstract