This article demonstrates a 39-GHz CMOS phasedarray beamformer aiming for power-efficient and area-efficient fifth-generation (5G) dual-polarized multiple-in-multiple-out (DP-MIMO) applications. To address the digital pre-distortion (DPD) implementation issue in the massive beamformer elements with Doherty technique integrated, an inter-element mismatch compensation technique is introduced for improving the shared-lookup table (LUT) DPD performance over the process, voltage and temperature (PVT) variations. A bidirectional Doherty power amplifier (PA)-LNA is proposed to enhance the power back-off (PBO) efficiency regarding the high peak-toaverage power ratio (PAPR) 5G signals, meanwhile cost down the system by the unbalanced neutralized bidirectional operation. The proposed phased-array beamformer chip is fabricated in 65-nm CMOS technology and packaged in a wafer-level chip-scale package (WLCSP). Each element occupies only a 0.82-mm 2 chip area, including the on-chip low-dropout regulator (LDO). The measured stand-alone Doherty PA-LNA achieves 18.9-dBm saturated output power with 17.8% power-added efficiency (PAE) at 6-dB PBO in PA mode and obtains a 4.8-dB noise figure (NF) at 40 GHz in LNA mode. By utilizing the proposed mismatch compensation, the measured 64-quadrature amplitude modulation (QAM) orthogonal frequency-division multiple access Manuscript

This article introduces a high-accuracy phase and amplitude detection circuit for 5G phased-array calibration. By utilizing a 39 GHz-150 kHz down-conversion scheme, the phase and amplitude information are detected separately with a phase-to-digital converter (PDC) and an analogto-digital converter (ADC). In addition, to reduce the number of reference signals, a divide-by-4 injection-locked frequency divider (ILFD) using a transformer-based injection-enhancing technique is implemented for wideband reference signal generation. This ILFD realizes a wide locking range of 16.3-23.4 GHz (35.8%) with 5.05-mW power consumption. The detection circuit achieves less than 0.049 • and 0.036-dB detection rms errors at 39 GHz. The wideband high-accuracy detection is also achieved from 37 to 43.5 GHz. The total power consumption is 50 mW with a 1-V VDD. The total core area is 1.43 mm 2 in a 65-nm CMOS process.

No abstract

This article introduces a power-efficient 24.25-71-GHz multi-band phased-array receiver supporting all allocated fifth-generation mobile network new radio (5G NR) frequency range 2 (FR2) bands at 24/28/39/47 GHz and the potential 5G NR-U bands in unlicensed 57-71 GHz. A novel harmonic-selection technique is introduced to extend the operating bandwidth with low power consumption. By switching between the fundamental-selected mode, the second-harmonicselected mode, and the third-harmonic-selected mode, only signals in the desired bands can be preserved, while the unselected mixing components are rejected. A dual-mode multi-band lownoise amplifier (LNA) based on a configurable transformer is adopted to realize broadband operation with minimized power consumption and noise figure (NF). The Hartley architecture is employed to further improve the image rejection performance. A hybrid-type polyphase filter (PPF) with a detectorbased high-precision calibration block is utilized in this work to realize the Hartley operation with reduced insertion loss (IL). The proposed phased-array receiver is fabricated in a standard 65-nm bulk CMOS process. With the concerted efforts of all components, the proposed multi-band receiver can support 5G standard-compliant OFDMA-mode modulated signals up to 256QAM with a 400-MHz channel bandwidth from 24 to 71 GHz. Better than 36-dB inter-band blocker rejections can be maintained by this work. With existing of 0-dBc inter-band blockers at worst case frequencies, this receiver

No abstract