Apple maggot fly, Rhagoletis pomonella (Walsh) is a major pest causing considerable economic losses of fruits in North America. During the development of international trade, apple maggot fly has become a threat to Chinese agriculture. In this study, CLIMEX and ArcGIS were used to predict the potential geographical distribution of apple maggot fly in China. The parameters used in CLIMEX for apple maggot fly were derived from ecological data and the present geographical distribution of apple maggot fly in North America. Then the potential distribution map in China was presented based on the adjusted values of these parameters. The results showed that apple maggot fly has a wide potential distribution area in China; 47.5% of 748 meteorological stations presented high or medium suitability of pest establishment. These high suitable stations are mainly located in northeast, southwest and northwest of China, such as Liaoning, Shandong, Gansu and Shaanxi Provinces. These areas are also the central regions of apple, pear and peach production in China. Two hundred and twenty‐five stations (30.1%) in western and southern China, such as Tibet, Qinghai, Guangdong, Guangxi, Hainan and Taiwan, were unsuitable for establishment of apple maggot fly populations. In order to prevent the introduction of apple maggot fly in China, the present plant quarantine measures should be enhanced, especially in the areas with high suitability for the presence of apple maggot fly.

In this paper, we mainly introduce the research status and development trend of welding numerical simulation technology. It is mainly reviewed that the simulation of molten pool flow field, welding temperature field and mechanical field, welding deformation and residual stress, hydrogen diffusion analysis, carbon migration of dissimilar steel welded joints, special welding process, microstructure of welded joints and grain growth process of welding heat affected zone. Then we discuss the special welding process simulation technology and special software for welding simulation. Finally, the development of welding numerical simulation technology in China are concerned.

The weld overlay technology of high strength low alloy steel (HSLA) and austenitic stainless steel is widely applied in such fields as petroleum, chemical industry and energy, and its service environment is of high temperature and corrosion. As the matching performance is often poor for both austenitic stainless steel and high strength low alloy steel, cavities and crackles occur easily at the joints, which cause brittle fractures with dangerousness to some extent. So in the present study, the metal-inert gas welding (MIG) is used to clad the austenitic stainless steel to HSLA. In the experimental group, 4mm buffer layer (E309L) and 8mm cladding layer (E347L) were successively cladded on the substrate (Q345B), while 12mm cladding layer was directly deposited on the substrate in the control group. The hot corrosion tests were done, and through the scanning electron microscope (SEM), we observed the cross-sectional morphology. By the X-ray diffraction (XRD), we analyzed ingredients of the corrosion products. The corrosion products in the experimental group mainly consist of iron and nickel oxides, while the products are mainly iron complex compound and salt in the control group. The SEM results show the area near the welding seam of the specimens without buffer layer had been corroded severely. However, only a slight corrosion occurs adjacent to the welding seam. This demonstrates that the buffer layer can protect the specimens from being corroded.

As new generation of low alloy high strength steel, WELDOX960 is extensively applied into heavy-duty fields including engineering machine etc. This paper adopts mixed gas protection welding to make multi-layer and multi-channel welding to low alloy high strength steel WELDOX960, using match methods with different intensities to prepare six groups of samples, respectively. The performances including joint tension and impact etc are tested for analysis after welding. The result shows that backing welding is the most important technique process in multi-layer and multi-channel welding, which has significant impact to joint performance, in the precondition that the strength is satisfied, if the material with lower strength is taken as backing layer, toughness and plasticity of the joint can be improved significantly. For example, tensile strength of sample 50-90 reaches 966.3Mpa, which is the same as 90-90, however, its toughness increases by 15%.

In this paper, according to the requirements of welder's technical qualification specification, combined with the practice training topic of TIG vertical butt welding, we have repeatedly trained the operation process of TIG vertical butt welding of q355g steel pipe with specification of Φ 60 х 5,And we adopt the following process measures in the welding process: before welding, we make V-shaped tooling by combining with the workpiece ; when welding, we choose reasonable process parameters; at the same time, we pay more attention to the welding operation skills of backing and cover layer. Therefore, we have achieved satisfactory weld quality, and the relevant experience has been popularized in the teaching process of the school to obtain good evaluation.