Periodontal disease is a common disease in the oral field, and many researchers are studying periodontal disease and try to find some biological scaffold materials to make periodontal tissue regenerative. In this study, we attempted to construct a carbon nanotube/chitosan/sodium alginate (CNT/CS/AL) ternary composite hydrogel and then prepare porous scaffold by 3D printing technology. Subsequently, characterizing the materials and testing the mechanical properties of the scaffold. Additionally, its effect on the proliferation of human periodontal ligament cells (hPDLCs) and its antibacterial effect on Porphyromonas gingivalis were detected. We found that CNT/CS/AL porous composite scaffolds with uniform pores could be successfully prepared. Moreover, with increasing CNT concentration, the degradation rate and the swelling degree of scaffold showed a downward trend. The compressive strength test indicated the elastic modulus of composite scaffolds ranged from 18 to 80 kPa, and 1% CNT/CS/AL group had the highest quantitative value. Subsequently, cell experiments showed that the CNT/CS/AL scaffold had good biocompatibility and could promote the proliferation of hPDLCs. Among 0.1%-1% CNT/CS/AL groups, the biocompatibility of 0.5% CNT/CS/AL scaffold performed best. Meanwhile, in vitro antibacterial experiments showed that the CNT/CS/AL scaffold had a certain bacteriostatic effect on P. gingivalis. When the concentration of CNT was more than 0.5%, the antimicrobial activity of composite scaffold was significantly promoted, and about 30% bacteria were inactivated. In conclusion, this 3D-printed CNT/CS/AL composite scaffold, with good material properties, biocompatibility and bacteriostatic activity, may be used for periodontal tissue regeneration, providing a new avenue for the treatment of periodontal disease.

Root canal (RC) therapy is the primary treatment of dental-pulp and periapical diseases. The mechanical method and chemical irrigation have limitations in RC therapy. Much attention has focused on exploring more controllable and efficacious antimicrobial methods. Although the introduction of photodynamic therapy (PDT) has provided the ideas for RC debridement, the problems of low photosensitive efficiency and nonsignificant germicidal potency of traditional photosensitizers (e.g., methylene blue) have not been solved. Since the concept of "aggregation-induced emission" (AIE) was proposed, optimization of photosensitizers has been boosted considerably. Herein, an AIE photosensitizer, DPA-SCP, with a strong ability to generate singlet oxygen, is proposed for use as an antibacterial application in infected RCs. The antimicrobial activity of DPA-SCP against Enterococcus faecalis suspensions was tested. To explore the antibacterial ability of this photosensitizer against bacterial-biofilm colonization on the inner walls of RCs, we established a model of bacterial biofilm infection. PDT mediated by DPA-SCP had a significant germicidal effect on E. faecalis suspensions and 21-day biofilms in human RCs. PDT mediated by DPA-SCP could achieve efficiency equivalent to that observed using 1% NaOCl, and lead to no significant change in the dentin surface, chemical corrosion, or cytotoxicity.

Oral and maxillofacial tumors, trauma and infections are the main causes of jaw defects, whose clinical treatment is very complicated. With the development of biological tissue engineering, many biological materials have been widely used in various fields of stomatology, and they play a very important role in the repair and replacement of maxillofacial bone defects. In this study, we intended to prepare a graphene oxide/hyaluronic acid/chitosan (GO/HA/CS) composite hydrogel with different mass ratios of GO: 0.1% (0.1% GO/HA/CS), 0.25% (0.25% GO/HA/CS), 0.5% (0.5% GO/HA/CS), and 1% (1% GO/HA/CS), prepare it into a multilayered and stable composite scaffold through 3D-printing technology, observe the surface morphology of the composite scaffold through scanning electron microscopy (SEM), and then test its physical and chemical properties, mechanical properties, water swelling rate, in vitro degradation and other material properties. Moreover, the biological performance of the GO/HA/CS composite scaffold was studied through experiments, such as cell morphology observation, cell adhesion, cell proliferation, and live-dead cell staining. The results showed that through chemical cross-linking and 3D-printing technology, a porous (pore size: 450–580 μm) and multilayered GO/HA/CS biological scaffold could be successfully constructed, and its surface was an interconnected microporous structure, and the porosity decreased (94%−40%) gradually with the increase of GO. Meanwhile, with the change in GO concentration, some mechanical properties of the scaffold could be improved, such as water swelling rate, degradation rate, and elastic modulus. In addition, the composite scaffold with the appropriate amount of GO had almost no cytotoxicity and could promote cell growth and proliferation, especially 0.25% GO/HA/CS composite scaffold. Consequently, the 0.25% GO/HA/CS composite scaffold had excellent biological material properties and good biocompatibility with osteoblasts, which may provide a new idea for the repair of jaw defects.