Coal is the basic resource underpinning energy generation in China, however, constant, large-scale mining of coal results in many problems such as ecological destruction of mining areas. As a result, backfilling of solid waste underground is proposed to control strata and surface subsidence and to protect the environment. At present, these materials, such as granular material, cemented material and high-water-content materials are mainly used for backfilling. This study summarised the types of backfill materials that are used in coal mines in China along with the backfilling process. Moreover, distribution and characteristics of mines backfilled with these backfill materials were obtained and analysed. Considering the socio-environmental aspects that affect backfilling, this research proposed a guideline for the selection of backfill materials and then analysed specific engineering cases of three backfill materials. In addition, the future development of backfill materials was discussed. With extensive extraction of shallow coal resources in China and, therefore, rapid depletion of coal resources in eastern regions of China, coal mining depth is increasing significantly. As a result, it is required to investigate new backfill materials suited for the deep high-stress environment.

China is the world’s largest coal producer country. However, large-scale coal mining has led to severe environmental pollution issues such as surface subsidence and gangue piling up. The gangue discharging amount has ranked the first in the world and coal mine enterprises are facing enormous discharging reduction pressure. This paper summarizes the research progress of the solid backfilling mining technology and then illustrates the realistic demands and significance of implementing underground coal-waste separation. It also focuses on the technical principles, systems and key equipment of the common underground coal-waste separation methods, such as the selective crushing method, the dense medium shallow groove method, the vibro-assisted jigging method and full-size water separation method and ray identification method. In addition, the selection steps of underground coal-waste separation method, the design process of large section separation chamber and the design principle of separation and backfilling system are proposed, finally, the mining-separating-backfilling + X for coal mining is put forward. By combining the technology of mining-separating-backfilling with other technologies, such as gob-side entry retaining with non-pillar mining, gas extraction, solid waste treatment, water protection mining, mining under buildings, railways and water bodies, the integrated mining methods, mining-separating-backfilling + setting pillars, gas drainage, treatment, protection and prevention methods are formed. It also introduced the ‘mining-separating-backfilling + gas extraction’ technology’s whole idea, system arrangement, separation equipment and practical engineering application effects based on the specific engineering case of pingmei no. 12 coal mine. The results indicate that the integration of underground coal-waste separation and solid backfilling technology could achieve gangue discharging reduction, underground washing and surface subsidence control. It is effective at realizing green mining.

Deep coal mining is unavoidable, and the complex mining environments and the increasing dangers associated with ultrahigh energy accumulation and release from mining disturbances renders it extremely difficult to maintain a safe and stable stope. Solid backfilling technology directly uses coal gangue and other solid wastes in the mining area to fill the gob after mining. Support from the backfill body can inhibit the movement of overlying rock strata and significantly alleviate the influence of mining. In this study, the correlations between the deformation of gangue filling material and the characteristics of energy dissipation were examined under lateral uniaxial compression. The strain energy density distributions of backfilling and caving mining methods were simulated using numerical modeling. The results showed that the strain energy density distribution of backfilling mining was less concentrated, and its peak value was lower than that of caving mining by 51.0%, indicating that backfilling could effectively reduce the amount of energy released from mining rocks. The dense backfill mining area of the No. 9301 face in Tangkou Coal Mine was used as a case study. Measures for controlling the backfill body compaction for reducing the amount of energy released from mining rocks were proposed. These measures include optimizing the support structure and filling material formula, controlling the preroof subsidence, and ensuring an appropriate number of tamping strokes. The monitoring results of the backfilling quality, surface subsidence, and microseismic energy of No. 9301 working face in Tangkou Coal Mine showed that when the backfill body filling ratio control value was 82.28%, the total number of microseisms and the amount of energy released from the mining working face were significantly lower compared to those of the caving method. This study demonstrated that the backfill body could effectively reduce the amount of energy released from mining rocks, thereby realizing management of mine earthquake and sustainable deep coal mining.

No abstract

The research aims to explore the influences of lithology on the compaction behaviours of broken waste rocks. For this purpose, a WAW-1000D servo test machine and a self-made bidirectional loading test system for granular materials were used to conduct axial and lateral compaction tests on four typical types of broken waste rocks: sandstone, mudstone, limestone and shale. On this basis, we analysed the relationships between lateral and axial stress with the strain in, and porosity of, the four types of broken waste rocks. In addition, the relationship of axial stress with lateral stress and lateral pressure coefficient, and the changes in the particle size distribution of broken waste rocks before and after compaction were discussed. The test results demonstrated that the samples of higher strength were found to have low lateral and axial strains as well as a lower porosity in axial and lateral loading tests, while samples of lower strength showed low lateral stress and lateral pressure coefficient under axial load. After being compacted, the samples of the four types of broken waste rocks were found to have a higher proportion of small particles, indicating some particle crushing. Moreover, the samples of lower strength were broken to a greater extent.