Abstract The microbial fuel cell (MFC) provides new opportunities for energy generation and wastewater treatment through conversion of organic matter into electricity by electrogenic bacteria. This study investigates the effect of different types and concentrations of substrates on the performance of a double chamber microbial fuel cell (DCMFC). Three mediator-less laboratory-scale DCMFCs were used in this study, which were equipped with graphite electrode and cation exchange membrane. The MFCs were fed with three different types of substrates (glucose, acetate and sucrose) at a chemical oxygen demand (COD) concentration of 1,000 mg/L. The selected substrate (acetate) was studied for three different concentrations of 500, 2,000 and 3,000 mg/L of COD. Results demonstrated that acetate was the best substrate among the three different substrates with maximum power density and COD removal of 91 mW/m2 and 77%, respectively. Concentration of 2,000 mg/L was the best concentration in terms of performance with maximum power density and COD removal of 114 mW/m2 and 79%, respectively. The polarization curve shows that ohmic losses were dominant in DCMFCs established for all three substrates and concentrations.

Liqui-solid technique and solid dispersion formation are two novel approaches for enhancement of dissolution rate of BCS class II drugs. Liqui-solid compact converts a liquid drug or drug solution into a free flowing powder with enhanced dissolution rate. In case of solid dispersion drug is molecularly dispersed in a hydrophilic polymer in solid state. In the present study, Liqui-solid and solid dispersion techniques were applied to enhance the dissolution of the Hydrochlorothiazide. Three formulations of Hydrochlorothiazide were prepared by liqui-solid technique using micro crystalline cellulose as carrier material and colloidal silicon dioxide as coating material. Water, poly ethylene glycol-400 and Tween-60 were used as solvent system. Solid dispersions of Hydrochlorothiazide were prepared by solvent fusion method using PEG-4000 as carrier polymer. Tablets were subjected to evaluation of various physical and chemical characteristics. Dissolution profiles of tablets prepared by the novel techniques were compared with marketed conventional tablets. Model independent techniques including similarity factor, dissimilarity factor and dissolution efficiency were applied for comparison of dissolution profiles. The results obtained indicated that liqui-solid compact formulations were more effective in enhancing the dissolution rate compared with solid dispersion technique. The liqui-solid compacts improved the dissolution rate up to 95% while the solid dispersion increased it to 88%.

Domperidone and Itopride are pro-kinetic agents, regulating the gastric motility and are commonly prescribed as anti emetic drugs. In the present study a simple, rapid and sensitive RP-HPLC/UV method was developed for simultaneous determination of Domperidone and Itopride in pharmaceutical samples and human plasma, using Tenofavir as internal standard. Experimental conditions were optimized and method was validated according to the standard guidelines. Combination of water (pH 3.0) and acetonitrile (65:35 v/v) was used as mobile phase, pumped at the flow rate of 1.5 ml/min. Detector wavelength was set at 210 nm and column oven temperature was 40oC. Unlike conventional liquid-liquid extraction, simple precipitation technique was applied for drug extraction from human plasma using acetonitrile for deprotienation. The method showed adequate separation of both the analytes and best resolution was achieved using Hypersil BDS C8 column (150 mm × 4.6 mm, 5 μm). The method was quite linear in the range of 20-600 ng/ml. Recovery of the method was 92.31% and 89.82% for Domperidone and Itopride, respectively. Retention time of both the analytes and internal standard was below 15 min. The lower limit of detection (LLOD) and lower limit of quantification (LLOQ) for Domperidone were 5 and 10 ng/ml while for Itopride was 12 and 15 ng/ml, respectively. The developed method was successfully applied for in-vivo analysis of fast dispersible tablets of Domperidone in healthy human volunteer. The proposed method was a part of formulation development study and was efficiently applied for determination of the two drugs in various pharmaceutical products and human plasma.

No abstract

Drug release from polymeric matrix systems is the rate-limiting step for drug bioavailability and is determined by drug solubility; most drugs show pH-dependent solubility. Polymeric matrices remain in the gastrointestinal tract for a longer period of time and are exposed to environments of varying pH, which can adversely affect drug release. In the present study, the pH-independent drug release of domperidone was achieved by modifying the microenvironmental pH of a swollen polymeric matrix using acidic excipients (citric acid and tartaric acid). Matrices were prepared by a water-based, wet-granulation technique and evaluated for various official and unofficial parameters. In vitro drug release was studied using USP dissolution apparatus and pH 6.80 phosphate buffer as dissolution medium. Release kinetics was evaluated according to various mathematical models.Results show that domperidone release can be effectively modified by inclusion of acidic excipients in the formulations. Acidic excipients modulated microenvironmental pH and avoided the effect of dissolution medium pH on drug release. The resultant formulations are easy to prepare and scale up for commercial manufacturing. Better pH-independent release, following zero-order kinetics, was achieved with tartaric acid.