Many scholars have focused on the workability and mechanical properties of fly ash (FA)- ground granulated blast furnace slag (GGBS) geopolymer. To enhance the compressive strength of geopolymer, zeolite powder was added in the present study. A series of experiments were carried out to investigate the effect of using zeolite powder as an external admixture on the per-formance of FA-GGBS geopolymer, 17 sets of experiments were designed and tested to deter-mine the unconfined compressive strength based on the response surface methodology, and then, the optimal parameters were obtained via modeling of 3 factors (zeolite powder dosage, alkali exciter dosage, and alkali exciter modulus) and 2 levels of compressive strength (3 d and 28 d). The experimental results showed that the strength of the geopolymer was the highest when the three factors were 13.3%, 40.3%, and 1.2. Finally, a combination of scanning electron microscopy (SEM), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), and 29Si nuclear magnetic resonance (NMR) analysis was used to conduct micromechanical analysis and explain the reaction mechanism from a microscopic perspective. The SEM and XRD analysis revealed that the microstructure of the geopolymer was the densest when the zeolite powder was doped at 13.3%, and the strength increased accordingly. The NMR and Fourier transform infrared spectroscopy analyses revealed that the absorption peak wave number band shifted toward the lower wave number band under the optimal ratio, and the silica–oxygen bond was replaced by an aluminum–oxygen bond, which generated more aluminosilicate structures.

In response to the high carbon emissions and energy consumption of traditional cement curing agents, in this paper, we propose a fly ash/slag-based geopolymer as an alternative to cement for stabilizing soft soils. In this study, the effects of the activator modulus, activator, and slag content on the geopolymer-stabilized clay were investigated by unconfined compressive strength (UCS) tests on Hangzhou soft soils, and the water stability and resistance to wet–dry cycles of the geopolymer-stabilized soils were studied. The changes in the microstructure and mineral phases were investigated using X-ray diffraction and scanning electron microscopy, respectively, and the inner evolution of the properties of the stabilized soft soil under different conditions was clarified. The test results revealed that the UCS of the geopolymer-stabilized soft soils increased and then decreased as the content and modulus of the alkali activator increased. The optimum mix proportion of geopolymer-stabilized soil required a modulus of the alkali activator of 0.6, a content of the alkali activator of 6%, and a slag-to-fly ash ratio of 1:1. Its 28-day UCS of the test specimens reached 2 MPa. When the content of the geopolymer was 25%, the water stability coefficient reached 87.53%, and the strength was still 1.6 MPa after eight wet–dry cycles. Based on the microscopic analysis, the cementing substances in the geopolymer-stabilized clay were calcium silicate hydrate (C-S-H) and sodium aluminosilicate hydrate (N-A-S-H), which made the soil’s structure denser through bonding and filling effects.

The ordinary Portland cement (OPC)-based solidification process is used extensively to reinforce soils due to its available and good bonding properties. Alternative products are used in cementitious materials to enhance the strength and to reduce OPC consumption. In this study, the effect of additive type and mass fraction on the microstructure and mechanical properties of solidified sandy silt are investigated. There are four types of additives (gypsum, lime, clay particles, and fly ash) at mass fractions of 2, 3, and 4% that are considered in order to study their mechanical properties (unconfined compression, indirect tensile, flexural strength, and compressive resilient modulus) at 7, 14, 28, 60, and 90 days. The optimal contents of additive gypsum, clay particles, and fly ash are determined to be 2%, 4%, and 4%, respectively. Such improvement of additive-modified OPC solidified sandy silt is due to the formation of the crystalline compound or the gradation composition improvement via field emission scanning electron and X-ray diffraction analysis.