The aim of this work is to study the immobilization ability of new composite materials based on polyethylene (PE) and polysaccharides (PS) in relation to the biocenosis of activated sludge (AS). The objects of the study were selected composite materials of the following composition: PE : pure microcellulose (MCc), PE : waste microcellulose (MCw), PE : starch (ST), at a ratio of components PE : PS = 70:30 wt.%. The objectives of the study were to determine the main morphological parameters of new composites (porosity, roughness, density), assessment of hydrochemical and hydrobiological state of AS (silt index, mass concentration of silt, species composition) until it locks into composites, assessment of the immobilization ability of the studied materials by biomass weight gain, monitoring of the state of AS after fixing. The tests found that the composite of structure of PE : MCc of has a density of 410 kg/m3 and a porosity of 60%, the roughness of 3.5; the composite of structure of PE : MCw has a density of 590 kg/m3 and a porosity of 40%, roughness of 2.0, composite of structure of PE : ST has a density of 640 kg/m3 and a porosity of 50%, the roughness of 2.5; wherein the reference sample - PE - has the parameters: density 860 kg/m3 and a porosity of 0%, roughness 0. To determine the immobilization capacity of the new composite materials, a laboratory experimental immobilizer was used, which is a container filled with 70% of the useful volume of the active sludge suspension and 30% of the floating loading samples. Immobilization was carried out under aeration conditions during 2, 4, 8, 12, 24, 48, 72 hours. As a result of tests it is established that the sample of structure of PE : MCc for 72 hours of immobilization showed a gain of biomass of the order of 12%, the sample of structure of PE : MCw - 5%, the sample of structure of PE : ST – 7%, PE – 3%. The condition of the organisms AS after fixing was evaluated by washings with immobilized samples, as a result of microscopy of washouts, the presence of living representatives of the biocenosis of AS in all samples was established, but they differ in number: for the sample of structure of PE : MCc - numerous, PE : MCw, PE : ST - average number, PE - small number. Further studies on the modification of the synthetic polyolefin matrix by functional fillers, including those from a number of polysaccharides, are of interest, allowing to increase the affinity of the carrier material with the extracellular matrix of activated sludge.

The article presents the results of a study of the rheological behavior of binary composites based on serial polyethylene grade LDPE 15803-020 with different content of microcellulose grade Filtracell, in a wide range of temperatures and shear rates during deformation through a capillary diameter of 1 mm and a length of 5 and 30 mm. Stable flow regime is manifested in the temperature range from 160 to 200°C for composites containing microcellulose in an amount of 30 wt.%, and its partial replacement with spent microcellulose (waste production of vegetable oils) can reduce the effective viscosity to 25%, but the upper limit of the temperature range is limited to the exudation of impurities (190°C). The Bagley correction is carried out, the coefficients of the equations describing the dependences of the true shear stress, regardless of the capillary length, are calculated.

No abstract

The paper presents the results of the evaluation of the destruction of polyethylene LDPE (hereinafter-PE), modified by prooxidants based on iron, copper and cobalt carboxylates (in the amount of 1.5 mass. % ) with accelerated thermal and ultraviolet aging for 192 hours. The assessment of degradation in the context of environmental safety included the determination of the degree of compliance of the materials with the requirements of state standard 33747-2016 "Oxo-biodegradable packaging", according to which the criterion of the efficiency of oxobiodestructionpolyolefins may be a decrease in strength and elongation at break of the sample at accelerated aging, as well as the quantitative determination of the release of formaldehyde during thermal degradation modified with prooxidants PE for comparison with the maximum permissible concentration. The rheological parameters of the materials were studied and a comparative assessment of the melt viscosity reduction and reduction with respect to elongation at break in the dynamics of accelerated thermal and UV aging of the PE modified with prooxidants in the selected time interval of 192 hours of exposure was carried out. A decrease in the relative elongation at rupture of PE containing cobalt - based prooxidant by 94% at thermal aging for 192 hours, and by 46% at ultraviolet was established. For PE modified with copper carboxylate, these values were 64 and 33 %, respectively, for PE modified with iron carboxylate – 35% and 40%, respectively. The reduction of strength by 95% of the initial value for 192 hours of temperature exposure was achieved in a sample modified with cobalt, which confirms its compliance with state standard 33747-2016. For other samples, the degree of strength reduction in the selected time interval does not allow to assess compliance with the specified standard. The release of formaldehyde during thermal aging for 192 hours per 1 g of the PE sample modified with cobalt carboxylate was 0.051 mg/m3, for PE modified with copper carboxylate – 0.032 mg/m3, for PE modified with iron carboxylate – 0.034 mg/m3. Installed excessive concentrations of formaldehyde in air hood PH with the carboxylate of cobalt 1.2 times under thermal aging 96 hours and 1.5 times the thermal ageing of a maximum of 192 hours. The reduction of the viscosity of PE containing cobalt – based prooxidant by 90% at thermal aging for 192 hours and by 10% at ultraviolet was recorded. For PE modified with copper carboxylate, these values were 9 and 2 %, respectively, for PE modified with iron carboxylate – 8 and 5%, respectively.

No abstract