Untitled

Djidjelli, Hocine; Martinez‐Vega, Juan; Farenc, J.; Benachour, Djafer

doi:10.1002/1439-2054(20020901)287:9<611::aid-mame611>3.0.co;2-l

Cited by 50 publications

(22 citation statements)

References 14 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…[345][346][347][348][349][350][351][352][353][354][355] These fillers are known to reduce thermal stability of PVC: copper-containing compounds, iron salts, cadmium, cobalt, manganese, lead salts (also other fillers containing these metals). [345][346][347][348][349][350][351][352][353][354][355] These fillers are known to reduce thermal stability of PVC: copper-containing compounds, iron salts, cadmium, cobalt, manganese, lead salts (also other fillers containing these metals).…”

Section: Fillersmentioning

confidence: 99%

Principles of Thermal Degradation

Wypych¹

2015

PVC Degradation and Stabilization

View full text Add to dashboard Cite

Section: Fillersmentioning

confidence: 99%

Principles of Thermal Degradation

Wypych¹

2015

PVC Degradation and Stabilization

View full text Add to dashboard Cite

“…A considerable amount of work has already been accomplished in the past few decades toward this target . Previously, fillers such as wood flour , clay , wood fibers , agricultural residues , cellulose whiskers , and calcium carbonate were employed to improve the thermal and mechanical stability of PVC. Recently, CNT have also been recognized as an appropriate filler material for PVC .…”

Section: Introductionmentioning

confidence: 99%

The effect of graphene nanosheets on the mechanical properties of polyvinylchloride

et al. 2014

View full text Add to dashboard Cite

In this work, excellent improvement in mechanical properties was observed by incorporating graphene nanofillers in polyvinyl chloride via solution blending. About 63% increase in modulus and 19% increase in ultimate tensile strength were measured at 1.5 wt% nanofiller content while almost no drop in elongation at break was observed. POLYM. COMPOS., 37:1572–1576, 2016. © 2014 Society of Plastics Engineers

show abstract

“…Polymer composites have recently received attention in the polymer industries, especially those composites between thermoplastics and natural fibers, because of good mechanical strength, cost savings, and favorable environmental profiles [12]. Unfortunately, information on the elongational flow properties of such composites has been very rare, and they need more scientific evidence for the improvement of their processabilities.…”

Section: Introductionmentioning

confidence: 99%

“…Most researchers have found that adding natural fibers, wood flour, wood pulp, sisal, flax, bamboo, sunhemp, pineapple, and jute into thermoplastics usually results in lower ultimate mechanical strength of the composites [14–23], although work has been done to improve the mechanical and engineering properties of such composites, including chemical surface treatments, reinforcements with glass fibers [24] and long natural fibers [25], reinforcement with nanofillers [26–28], and processing and die designs [12]. Méndez et al [14] found that the mechanical strength of PP decreased with increasing wood pulp content because of PP and wood incompatibilities.…”

Section: Introductionmentioning

confidence: 99%

Mechanical strengths of molten and solidified LLDPE/LDPE blends and wood/LDPE composites under tensile deformation

Harnnarongchai¹,

Sitticharoen²,

Intawong³

et al. 2011

Vinyl Additive Technology

View full text Add to dashboard Cite

The mechanical strengths of neat low‐density polyethylene (LDPE), a blend of LDPE with linear low‐density polyethylene (LLDPE), and a composite of LDPE with wood flour (wood/LDPE) were investigated in molten and solidified states under tensile deformation. The results are discussed in terms of the effects of LLDPE and wood contents, roller speed, and volumetric flow rate. In LLDPE/LDPE blends, incorporating LLDPE from 0 to 30 wt% into LDPE caused a slight increase in drawdown force, a larger fluctuation in drawdown force, and a reduction of maximum roller speed to failure. The mechanical properties of the solidified LLDPE/LDPE corresponded to those of the molten LLDPE/LDPE with regard to the effect of LLDPE content. For wood/LDPE composites, increasing the wood flour content in molten LDPE caused considerable reductions in drawdown time and maximum roller speed to failure. The drawdown force increased with increasing wood flour up to 10 wt% before it decreased at the wood loading of 20 wt%. A number of voids and pores on the extrudate surfaces became obvious for the composites with 20 wt% of wood content. Increasing wood content enhanced the tensile modulus for the solidified LDPE but decreased its tensile strength. Unlike those of LLDPE/LDPE blends, the changes in tensile modulus and strength of solidified wood/LDPE composites with wood content did not correspond to those of the molten composites. In all cases, the drawdown force increased with increasing roller speed. The effect of volumetric flow rate from the extruder on the mechanical strengths of the solidified blends was more pronounced than on those of the molten ones. J. VINYL ADDIT. TECHNOL., 2011. © 2011 Society of Plastics Engineers

show abstract

Untitled

Cited by 50 publications

References 14 publications

Principles of Thermal Degradation

Principles of Thermal Degradation

The effect of graphene nanosheets on the mechanical properties of polyvinylchloride

Mechanical strengths of molten and solidified LLDPE/LDPE blends and wood/LDPE composites under tensile deformation

Contact Info

Product

Resources

About