2023
DOI: 10.1007/s12633-023-02466-8
|View full text |Cite
|
Sign up to set email alerts
|

A Comprehensive Review of Tandem Solar Cells Integrated on Silicon Substrate: III/V vs Perovskite

Abstract: High-efficiency solar cells with low manufacturing costs have been recently accomplished utilizing different technologies. III-V-based tandem solar cells have exhibited performance enhancement with a recent efficiency of greater than 39% under AM1.5G and 47% under concentration. Integration of such III-V materials on a relatively cheap Silicon (Si) substrate is a potential pathway to fabricate high-efficient low-cost tandem solar cells. Besides, perovskite solar cells, as third-generation thin film photovoltai… Show more

Help me understand this report

Search citation statements

Order By: Relevance

Paper Sections

Select...
1
1
1
1

Citation Types

0
5
0

Year Published

2023
2023
2024
2024

Publication Types

Select...
7
1

Relationship

0
8

Authors

Journals

citations
Cited by 16 publications
(5 citation statements)
references
References 144 publications
0
5
0
Order By: Relevance
“…When D is 3 m, the linear loss of the amount of direct solar radiation in the floating PV system is minimal, and the optimal state is reached. Since only geometric factors, including D, H, and ȕ are considered, the loss of the offshore PV system is always less than that of the onshore PV system at the same value of D. For bi-PV modules, the power generation is dominated by the front surface and could be further enhanced by the rear surface to a certain degree [4]. The power generation from the rear surface is more significantly determined by the temperature (directly related to the H value) and reflectivity (Refl).…”
Section: Resultsmentioning
confidence: 99%
“…When D is 3 m, the linear loss of the amount of direct solar radiation in the floating PV system is minimal, and the optimal state is reached. Since only geometric factors, including D, H, and ȕ are considered, the loss of the offshore PV system is always less than that of the onshore PV system at the same value of D. For bi-PV modules, the power generation is dominated by the front surface and could be further enhanced by the rear surface to a certain degree [4]. The power generation from the rear surface is more significantly determined by the temperature (directly related to the H value) and reflectivity (Refl).…”
Section: Resultsmentioning
confidence: 99%
“…TiO 2 behaved as an active material that absorbed photons and converted them into electric current, having a band gap around 3.2-3.8 eV, which allows the effective absorption of UV light [33,34]. The influence of TiO 2 inclusion on the following SC characteristics, respectively, was considered: (1) the open-circuit voltage (V oc ); (2) the short-circuit current (J sc ); (3) the SC conversion efficiency (η); and (4) the fill factor (FF). In order to obtain essential knowledge of SHTSC design, it is required to determine the optimized values of the SC physical parameters.…”
Section: Simulation Results For Electrical Modelling Of Shtscmentioning
confidence: 99%
“…Coatings 2024, 14, x FOR PEER REVIEW 11 of 16 (1) The SC electrical parameters were obtained based on the DD (defect density) of the IDL (interface defect layer) for different thicknesses.…”
Section: Analysis Of Interface Defects In Shtscsmentioning
confidence: 99%
See 1 more Smart Citation
“…Further development has either already occurred or is anticipated due to thin--film cell technology and third-generation PV cells, mainly DSSC (Parasuraman, 2023), organic (Prasad et al, 2013), perovskite (Park, 2015), as well as tandem solutions that combine more than one semiconductor material (Saif et al, 2023), such as graphene-based PV cells, which are known as fourth-generation cells (Pastuszak & Węgierek, 2022). nineteen-eighties application in architecture (based on adding a PV installation to an existing facility)…”
Section: Bipv -Definitionmentioning
confidence: 99%