A study of the deformation of weft-knit preforms for advanced composite structures Part 2: The resultant composite

Savci, S.; Curiskis, J.I.; Pailthorpe, M.T.

doi:10.1016/s0266-3538(00)00078-6

Cited by 16 publications

(11 citation statements)

References 12 publications

Supporting

Mentioning

Contrasting

Unclassified

Order By: Relevance

“…However, in many published papers [15,16], the change of angles of grids or textiles is measured and quantitative discussion is made. Quite similar study is also found in resin transfer molding (RTM) [17,18]. The problem is that the angle change is valid as the definition of shear strain only within the infinitesimal deformation.…”

Section: Digital Image-based Measurement Technique Of Large Strain DImentioning

confidence: 59%

Study on large deformation characteristics of knitted fabric reinforced thermoplastic composites at forming temperature by digital image-based strain measurement technique

Takano

Zako

Fujitsu

et al. 2004

Composites Science and Technology

View full text Add to dashboard Cite

Section: Digital Image-based Measurement Technique Of Large Strain DImentioning

confidence: 59%

Study on large deformation characteristics of knitted fabric reinforced thermoplastic composites at forming temperature by digital image-based strain measurement technique

Takano

Zako

Fujitsu

et al. 2004

Composites Science and Technology

View full text Add to dashboard Cite

“…Savci, Curiskis ve Pailthorpe daha önce şekil alabilirliğini inceledikleri cam ipliği atkılı örme kumaşlardan helikopter kapı cebi kompozit malzemesi üretmişlerdir [8,9]. Araştırmacılar şekil alabilirliği etkileyen faktörleri: takviye kumaşının uzayabilirliği, ortaya çıkan nihai kompozit ürününün kalitesine bağlı olarak içerdiği hataların seviyesi ve takviye kumaşının kompozit içerisindeki uzama dağılımı olarak sıralamışlardır.…”

Section: The Investigation Of 3d Formability Of Plain Wovenunclassified

Cam İpli̇ği̇nden Dokunmuş Bez Ayaği Kumaşin Üç Boyutlu Şeki̇l Alabi̇li̇rli̇ği̇ni̇n İncelenmesi̇

Ince¹

2019

Ömer Halisdemir Üniversitesi Mühendislik Bilimleri Dergisi

View full text Add to dashboard Cite

Lif takviyeli polimer kompozit malzeme üretiminde tekstil takviye kumaşının karmaşık şekilli kalıba kolaylıkla yatması istenen bir özelliktir. Bu çalışmada cam ipliğinden üretilmiş bezayağı dokuma kumaşın üç boyutlu şekil alabilirliği kumaş patlatma test cihazı kullanılarak Kubbe alanı olara (basınç artış) çevrim sayısı beş olarak belirlenmiştir. Kubbe alanının cm kaydedilen şişme değerleri normal bir dağılım göstermemiştir. Düşük basınç artış hızında şişme sergilemişlerdir. Çevrim sayısının artması ile birlikte kumaş şişmesi de artmıştır. Anahtar kelimeler:In the production of fiber fabric to readily lie in a complex, three woven glass fabric was measured using fabric bursting strength tester were rates were selected as cycles was set to 5. As the dome area increased, the amount of fabric distension increased. Distension measurements not. The fabrics exhibited more distension at low pressure increase rate. Fabric distension increased with the increase in the number of cycles.

show abstract

“…Draping of textile fabrics onto rigid moulds is extensively studied in composites material science [7,9]. However, such studies for knitted fabrics are scarce [10][11][12], probably due to the fact that use of knitted reinforcements is limited to applications where the material stiffness is not the main requirement. Knitted fabrics are highly deformable, and do not cause draping problems, like wrinkling, when used as reinforcement for composites (e.g.…”

Section: Introductionmentioning

confidence: 99%

Steel fibre knitted fabric for automotive glass forming: Variations of the fabric thickness on the mould and glass optical quality

Barburski

Lomov

Lanckmans

et al. 2014

Journal of Industrial Textiles

View full text Add to dashboard Cite

Extremely fine steel fibres (12 mm diameter) are spun into yarns and then knitted into fabric, which is used, among other applications, as a mould cover in the formation of automotive glass. High requirements of the glass quality (absence of dioptric distortions) ask for a perfect evenness of the mould cover surface, which depends on the local distortions of the fabric created during tensioning of the fabric over the mould. In this paper, compression behaviour of steel knitted fabrics combined with the fabric deformation in biaxial tension and shear is studied. Interaction of the fabric with the formed glass depends on the local changes of the fabric compression behaviour due to local fabric deformations on the mould. The deformation of the fabric is further linked to quality of the glass using quantitative optical distortion system based on moiré patterns to measure glass dioptric distortions.

show abstract

A study of the deformation of weft-knit preforms for advanced composite structures Part 2: The resultant composite

Cited by 16 publications

References 12 publications

Study on large deformation characteristics of knitted fabric reinforced thermoplastic composites at forming temperature by digital image-based strain measurement technique

Study on large deformation characteristics of knitted fabric reinforced thermoplastic composites at forming temperature by digital image-based strain measurement technique

Cam İpli̇ği̇nden Dokunmuş Bez Ayaği Kumaşin Üç Boyutlu Şeki̇l Alabi̇li̇rli̇ği̇ni̇n İncelenmesi̇

Steel fibre knitted fabric for automotive glass forming: Variations of the fabric thickness on the mould and glass optical quality

Contact Info

Product

Resources

About