A Two-Row Interdigitating-Finger Repulsive-Torque Electrostatic Actuator and Its Application to Micromirror Vector Display

Abstract

This paper presents a novel two-row interdigitatingfinger repulsive-torque electrostatic actuator and its application to the micromirror vector display. The actuator consists of upper and lower rotation units and an output beam. Each unit has one row of rotation fingers, i.e., the lower and upper rotation fingers, which interdigitate with each other. The lower and upper rotation fingers are subject to different electric potentials. Each rotation finger and its underneath aligned fixed finger are subject to the same electric potential. The actuator generates repulsive torques to rotate the lower and upper fingers out-of-plane with the maximum rotation not limited either by the gap between fingers and the substrate nor by the pull-in effect. The output beam is connected to the lower row of rotation fingers, and therefore, the actuator has the same rotation as the lower unit. The actuator requires only two thin films and is suitable for surface micromachining. The model is established to verify the actuator and calculate its performance. Prototypes are fabricated and tested. The experimental results show that the actuator achieved a mechanical rotation of 11.5°at the static driving voltage of 150 V and a resonant frequency of 380 Hz with a sinusoidal driving voltage varying from 20 to 70 V. This paper demonstrates the application of the actuator in micromirror vector display. Four actuators are connected to the peripheries of a micromirror plate and independently controlled to drive the mirror plate to achieve quasi-static 2-D rotation. A laser beam is reflected and steered by the mirror plate to any desired direction to realize vector display. The prototype of the vector display micromirror is fabricated and tested. A vector display module integrating the micromirror, a laser, and a concave lens is built. Based on this module, an automotive head-up display system is developed, which is able to display the navigation map, speed, turning sign, and vehicle location on a translucent screen.[ 2015-0098]Index Terms-Two-row interdigitating-finger, repulsive-torque electrostatic actuator, surface micromachining, micromirror vector display, head-up display (HUD).

Merging parallel-plate and levitation actuators to enable linearity and tunability in electrostatic MEMS

“…However, to account for fabrication imperfections the natural frequency is identified from an experiment and nondimensionalized to use with Equation (9). After separation of variables, the governing equation is multiplied by φ and integrated over x to yield Equation (10), which is a second-order ordinary differential equation that depends only on the time-dependent component of the solution, q,…”

“…One alternative to parallel-plate actuation is electrostatic levitation [8][9][10][11][12][13] . The electrode configuration shown in Figure 1 creates an electric field that pushes electrodes apart instead of pulling them together.…”

A reliable MEMS switch using electrostatic levitation

“…MEMS switches [1][2][3][4] , accelerometers 5,6 , microphones 7,8 , micro-mirrors [9][10][11][12][13] , and pressure sensors 14 all use electrostatics to operate. The working principle behind electrostatic actuation can be explained through a parallel plate capacitor, where two parallel plates are given some initial charge to create an electric field between them.…”

“…Much effort has been placed in creating electrostatic MEMS designs that do not experience pull-in at all. One of these methods is by actuating a structure using electrostatic levitation [9][10][11][12][13][16][17][18][19][20][21][22][23] . This involves a slightly different electrode configuration than the standard parallel plate design, with two extra electrodes that help induce an effectively repulsive force instead of an attractive one.…”

Micromirror-based real image laser automotive head-up display

“…Microsystem technology and MEMS (microelectromechanical systems) micromirrors have been intensively developed in the past 2 decades and have found various applications due to its high integration, small size, and suitability for low-cost batch production [6][7][8][9][10][11][12] . Micromirror-based laser vector scanning automotive HUDs were previously developed [13][14][15][16] with the core component to be an electrostatic repulsiveforce-driven micromirror [17][18][19][20][21][22] . Micromirrors' development has made significant progress with the major application in projectors [23] .…”