Advances in Physical Metallurgy and Processing of Steels. Physical Metallurgy of Modern High Strength Steel Sheets.

Senuma, Takehide

doi:10.2355/isijinternational.41.520

Cited by 236 publications

(96 citation statements)

References 22 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…[22][23][24][25] Since the presence of various texture components in the hot band of ULC steels seems to be unclear, the present work was conducted to study the effect of composition, mainly carbon, Ti and Nb, and thermomechanical processing variables on the formation of hot band texture in ULC steels. The main processing variables studied were the slab reheating temperature and the finishing temperature of the deformation in the austenite region.…”

Section: Introductionmentioning

confidence: 99%

Effect of Chemical Composition and Thermomechanical Processing on Texture in Hot Bands of Ti and Ti+Nb Containing Ultra-low Carbon Steels

et al. 2003

View full text Add to dashboard Cite

The effect of carbon, Ti and Nb on the formation of hot band texture in ultra-low carbon steels was studied. The chemical compositions were selected so that two of the four steels were fully stabilized with respect to carbon and the other two were expected to have some carbon in solution under equilibrium conditions. The slab reheating temperature ranged from 1 200 to 1 280°C. The first deformation was applied with a 50 % reduction to simulate the roughing pass at 1 150°C. The samples were then deformed with another 50 % reduction at either 1 050 or 920°C. The crystallographic orientations of the resulting ferrite were presented in the form of so-called skeleton plots along the RD-, TD-and ND-fibers. The main texture found was the cube-on-corner, {111}͗110͘, component. The rotated cube component, {001}͗110͘, was also present but its intensity was always lower than the intensity of the cube-on-corner component. The presence of the cube-on-corner texture was explained by the large grain size in the starting as-cast ingots and by the heavy reductions per pass. The combination of low reheating temperature and low finishing temperature generated the highest ratio of {111}/{100}. Decreasing the carbon content from 35 to 17 ppm and adding 90 ppm Nb to a Ti-alloyed ULC steel further increased the {111}/{100} ratio.

show abstract

Section: Introductionmentioning

confidence: 99%

Effect of Chemical Composition and Thermomechanical Processing on Texture in Hot Bands of Ti and Ti+Nb Containing Ultra-low Carbon Steels

et al. 2003

View full text Add to dashboard Cite

show abstract

“…Nao UEHATA, 1) Motomichi KOYAMA, 1) * Shusaku TAKAGI 2) and Kaneaki TSUZAKI 1) 1) Department of Mechanical Engineering, Kyushu University, Motooka 744, Nishi-ku, Fukuoka, Fukuoka, 819-0395 Japan. 2) Steel Research Laboratory, JFE Steel Corporation, 2-3, Uchisaiwai-cho 2-chome, Chiyoda-ku, Tokyo, 100-0011 Japan.…”

Section: Optical Microscopy-based Damage Quantification: An Example Omentioning

confidence: 99%

“…1,2) The superior mechanical properties are attributed to its high work-hardening capability associated with the large difference in strength between ferrite and martensite. 3) However, the high mechanical contrast causes microstructurally-local plastic strain 4) and the formation of micro-damage such as voids and cracks, 5) which degrade the local deformability 6) and change the apparent Young's modulus.…”

Section: Introductionmentioning

confidence: 99%

Optical Microscopy-Based Damage Quantification: an Example of Cryogenic Deformation of a Dual-Phase Steel

Uehata

Koyama

Takagi³

et al. 2018

ISIJ Int.

View full text Add to dashboard Cite

“…According to statistics, fuel consumption can be reduced by 0.6% to 1% with 1% reduction in car weight. So the lightweight of automobile is an important way to cut down oil consumption [1].…”

Section: Introductionmentioning

confidence: 99%

Investigate earing of TWIP steel sheet during deep-drawing process by using crystal plasticity constitutive model

Yang

Cai

Sun

et al. 2015

MATEC Web of Conferences

View full text Add to dashboard Cite

Abstract. By combining the nonlinear finite element analysis techniques and crystal plasticity theory, the macroscopic mechanical behaviour of crystalline material, the texture evolution and earing-type characteristics are simulated accurately. In this work, a crystal plasticity model exhibiting deformation twinning is introduced based on crystal plasticity theory and saturation-type hardening laws for FCC metal Fe-22Mn-0.6C TWIP steel. Based on the CPFE model and parameters which have been determined for TWIP steel, a simplified finite element model for deep drawing is promoted by using crystal plasticity constitutive model. The earing characteristics in typical deep-drawing process are simulated well. Further, the drawing forces are calculated and compared to the experimental results from reference. Meanwhile, the impacts of drawing coefficient and initial texture on the earing characteristics are investigated for controlling the earing.

show abstract

Advances in Physical Metallurgy and Processing of Steels. Physical Metallurgy of Modern High Strength Steel Sheets.

Cited by 236 publications

References 22 publications

Effect of Chemical Composition and Thermomechanical Processing on Texture in Hot Bands of Ti and Ti+Nb Containing Ultra-low Carbon Steels

Effect of Chemical Composition and Thermomechanical Processing on Texture in Hot Bands of Ti and Ti+Nb Containing Ultra-low Carbon Steels

Optical Microscopy-Based Damage Quantification: an Example of Cryogenic Deformation of a Dual-Phase Steel

Investigate earing of TWIP steel sheet during deep-drawing process by using crystal plasticity constitutive model

Contact Info

Product

Resources

About