An Investigation of the Composition of the Flow in and out of a Two-stroke Diesel engine and Air Consumption Ratio

Grljušić, Mirko; Tolj, Ivan; Radica, Gojmir

doi:10.20944/preprints201705.0192.v1

2017

DOI: 10.20944/preprints201705.0192.v1

|View full text |Cite

Preprint

An Investigation of the Composition of the Flow in and out of a Two-stroke Diesel engine and Air Consumption Ratio

Mirko Grljušić¹,

Ivan Tolj²,

Gojmir Radica³

Abstract: Abstract:The aim of this research was to investigate the mass, substances and energy flow through two-stroke low speed Diesel engines. For this reason, a zero-dimensional model of the combustion in the engine was developed with a calculated amount and composition of exhaust gases. Due to the large amount of oxygen in the exhaust gases, a ratio of real air consumption and stoichiometric amount of air required for combustion of injected fuel was set. The calculated ratio showed that the engine consumes four time… Show more

Help me understand this report

View published versions

Search citation statements

Order By: Relevance

Paper Sections

Select...

Citation Types

Supporting

Mentioning

Contrasting

Year Published

2018

2022

Publication Types

Select...

Article3

Relationship

Self Cite0

Independent3

Authors

Journals

Cited by 3 publications

References 10 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

Scavenging Ports’ Optimal Design of a Two-Stroke Small Aeroengine Based on the Benson/Bradham Model

et al. 2018

View full text Add to dashboard Cite

The two-stroke engine is a common power source for small and medium-sized unmanned aerial vehicles (UAV), which has wide civil and military applications. To improve the engine performance, we chose a prototype two-stroke small areoengine, and optimized the geometric parameters of the scavenging ports by performing one-dimensional (1D) and three-dimensional (3D) computational fluid dynamics (CFD) coupling simulations. The prototype engine is tested on a dynamometer to measure in-cylinder pressure curves, as a reference for subsequent simulations. A GT Power simulation model is established and validated against experimental data to provide initial conditions and boundary conditions for the subsequent AVL FIRE simulations. Four parameters are considered as optimal design factors in this research: Tilt angle of the central scavenging port, tilt angle of lateral scavenging ports, slip angle of lateral scavenging ports, and width ratio of the central scavenging port. An evaluation objective function based on the Benson/Bradham model is selected as the optimization goal. Two different operating conditions, including the take-off and cruise of the UAV are considered. The results include: (1) Orthogonal experiments are analyzed, and the significance of parameters are discussed; (2) the best factors combination is concluded, followed by simulation verification; (3) results before and after optimization are compared in details, including specific scavenging indexes (delivery ratio, trapping efficiency, scavenging efficiency, etc.), conventional performance indicators, and the sectional views of gas composition distribution inside the cylinder.

show abstract

Scavenging Ports’ Optimal Design of a Two-Stroke Small Aeroengine Based on the Benson/Bradham Model

et al. 2018

View full text Add to dashboard Cite

show abstract

Low-Speed Marine Diesel Engine Modeling for NOx Prediction in Exhaust Gases

et al. 2021

View full text Add to dashboard Cite

Knowing the process of generating exhaust emissions and the determination of influential parameters are important factors in improving two-stroke slow-speed marine engines, particularly for further reductions in fuel consumption and stringent regulations on the limitation of nitrogen oxide emissions. In this article, a model of a marine low-speed two-stroke diesel engine has been developed. Experimental and numerical analyses of the nitrogen monoxide formations were carried out. When measuring the concentration of nitrogen oxides in the exhaust emissions, the amount of nitrogen dioxide (NO2) is usually measured, because nitrogen monoxide is very unstable, and due to the large amount of oxygen in the exhaust gases, it is rapidly converted into nitrogen dioxide and its amount is included in the total emission of nitrogen oxides. In this paper, the most significant parameters for the formation of nitrogen monoxide have been determined. Model validation was performed based on measured combustion pressures, engine power, and concentrations of nitrogen oxides at 50% and 75% of maximum continuous engine load. The possibilities of fuel consumption optimization and reduction in nitrogen monoxide emissions by correcting the injection timing and changing the compression ratio were examined. An engine model was developed, based on measured combustion pressures and scavenging air flow, to be used on board by marine engineers for rapid analyses and determining changes in the concentration of nitrogen oxides in exhaust emissions. The amount of nitrogen oxide in exhaust emissions is influenced by the relevant features described in this paper: fuel injection timing and engine compression ratio. The presented methodology provides a basis for further research about the simultaneous impact of changing the injection timing and compression ratio, exhaust valve opening and closing times, as well as the impact of multiple fuel injection to reduce consumption and maintain exhaust emissions within the permissible limits.

show abstract

CFD Analysis of a Large Marine Engine Scavenging Process

et al. 2022

View full text Add to dashboard Cite

The scavenging process is an important part of the two-stroke engine operation. Its efficiency affects the global engine performance such as power, fuel consumption, and pollutant emissions. Slow speed marine diesel engines are uniflow scavenged, which implies inlet scavenging ports on the bottom of the liner and an exhaust valve on the top of the cylinder. A CFD model of such an engine process was developed with the OpenFOAM software tools. A 12-degree sector of the mesh was used corresponding to one of the 30 scavenging ports. A mesh sensitivity test was performed, and the cylinder pressure was compared to experimental data for the analyzed part of the process. The scavenging performances were analyzed for real operation parameters. The influence of the scavenge air pressure and inlet ports geometric orientation was analyzed. The scavenging process is analyzed by means of a passive scalar representing fresh air in the cylinder. Isosurfaces that show the concentration of fresh air were presented. The variation of oxygen and carbon dioxide with time and the axial and angular momentum in the cylinder were calculated. Finally, the scavenging performance for the various operation parameters was evaluated by means of scavenging efficiency, charging efficiency, trapping efficiency, and delivery ratio. It was found that the scavenging efficiency decreases with the engine load due to the shorter time for the process. The scavenging efficiency increases with the pressure difference between the exhaust and scavenging port, and the scavenging efficiency decreases with the increase in the angle of the scavenging ports. It was concluded that smaller angles than the industry standard of 20° could be beneficial to the scavenging efficiency. In the investigation, the charging efficiency ranged from 0.91 to over 0.99, the trapping efficiency ranged from 0.54 to 0.83, the charging efficiency ranged from 0.78 to 0.92, and the delivery ratio ranged from 1.21 to 2.03.

show abstract

scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.

Contact Info

customersupport@researchsolutions.com

10624 S. Eastern Ave., Ste. A-614

Henderson, NV 89052, USA

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

Blog Terms and Conditions API Terms Privacy Policy Contact Cookie Preferences Do Not Sell or Share My Personal Information

Made with 💙 for researchers

Part of the Research Solutions Family.

An Investigation of the Composition of the Flow in and out of a Two-stroke Diesel engine and Air Consumption Ratio

Cited by 3 publications

References 10 publications

Scavenging Ports’ Optimal Design of a Two-Stroke Small Aeroengine Based on the Benson/Bradham Model

Scavenging Ports’ Optimal Design of a Two-Stroke Small Aeroengine Based on the Benson/Bradham Model

Low-Speed Marine Diesel Engine Modeling for NOx Prediction in Exhaust Gases

CFD Analysis of a Large Marine Engine Scavenging Process

Contact Info

Product

Resources

About