An investigation on the explosive cladding of 316L stainless steel-din-P355GH steel

Kaçar, Ramazan; Acarer, Mustafa

doi:10.1016/j.jmatprotec.2004.03.012

Cited by 145 publications

(32 citation statements)

References 10 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The HCCI was chosen for its high wear-resistance and hardness, whereas the MCS for high strength property to resist impacting. Currently, there are several fabrication methods of bimetal, such as casting [5], diffusion bonding [6,7], rolling [8], extrusion [9], cladding [10,11] and powder metallurgy technology [12]. The casting as a simple, economical and effective method for fabricating bimetal has been confirmed [5], as well as was used in the current study.…”

Section: Introductionmentioning

confidence: 91%

Effect of volume ratio of liquid to solid on the interfacial microstructure and mechanical properties of high chromium cast iron and medium carbon steel bimetal

Xiong

Cai

Lü

2011

Journal of Alloys and Compounds

View full text Add to dashboard Cite

Section: Introductionmentioning

confidence: 91%

Effect of volume ratio of liquid to solid on the interfacial microstructure and mechanical properties of high chromium cast iron and medium carbon steel bimetal

Xiong

Cai

Lü

2011

Journal of Alloys and Compounds

View full text Add to dashboard Cite

“…These results were consistent with those reported by other researchers. 25,26) The results obtained from the vortices exhibited significantly different hardness values as shown in Fig. 5.…”

Section: Micro Hardnessmentioning

confidence: 97%

Explosive Welding of Titanium/Stainless Steel by Controlling Energetic Conditions

et al. 2006

View full text Add to dashboard Cite

Commercially pure titanium and 304 stainless steel were welded using explosive welding technique. The joints were evaluated using optical microscope, scanning electron microscope, energy dispersive spectroscopy and X-ray diffraction. The study indicates the formation of characteristic interfacial oscillations with vortices at high energetic conditions. The reacted products of the vortices have been identified as FeTi and Fe 2 Ti intermetallics by X-ray diffraction. Increase in the kinetic energy spent at the interface cause the volume of vortices to increase. Smooth wavy and flat topography has been obtained for thin flyer plates due to less kinetic energy loss. The results demonstrate a good welding interface for multi-layered welding using a thin stainless steel interlayer, as the kinetic energy dissipation at the interface was less.

show abstract

“…Research shows that the mechanical properties can be strongly linked to the microstructure and the phases formed by local fusion at the interface [19,20]. This paper presents the investigations of cobalt based superalloy cladding on steel by explosive cladding.…”

Section: Introductionmentioning

confidence: 99%

Cobalt-based superalloy layers deposited on X38CrMoV5 steel base metal by explosion cladding process

Ettaqi

Langlois

Bigot

2008

Surface and Coatings Technology

View full text Add to dashboard Cite

is an open access repository that collects the work of Arts et Métiers ParisTech researchers and makes it freely available over the web where possible. Thus cobalt retains its crystallographic structure (f.c.c) after cladding process. Hardness is evaluated with reference to microstructure. Near the interface, the hardness of the superalloy is of the order of 600 HV 1 kg . In the remainder of the thickness, hardness is of the order of 500 HV 1 kg , being greater than that of the unplated superalloy (270 HV 1 kg ). The track obtained by an indentation test at the interface under a load of 100 kg exhibits no cracking. This tends to prove the good metallurgical bond at the interface.

show abstract

An investigation on the explosive cladding of 316L stainless steel-din-P355GH steel

Cited by 145 publications

References 10 publications

Effect of volume ratio of liquid to solid on the interfacial microstructure and mechanical properties of high chromium cast iron and medium carbon steel bimetal

Effect of volume ratio of liquid to solid on the interfacial microstructure and mechanical properties of high chromium cast iron and medium carbon steel bimetal

Explosive Welding of Titanium/Stainless Steel by Controlling Energetic Conditions

Cobalt-based superalloy layers deposited on X38CrMoV5 steel base metal by explosion cladding process

Contact Info

Product

Resources

About