Comparison of Different Heat Exchanger Tube Designs used in Latent Heat Thermal Energy Storage Systems - a Numerical Study

Koller, Martin; Beck, Anton; Walter, Heimo; Hameter, Michael

doi:10.1016/b978-0-444-63428-3.50051-5

Cited by 2 publications

(2 citation statements)

References 5 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Numerical investigations on the melting behavior of PCM were conducted by Koller et al. [26] , Walter et al. [27] who also include the solidification process in their research and Diao et al.…”

Section: Introductionmentioning

confidence: 99%

Partial cycle operation of latent heat storage with finned tubes

et al. 2020

Self Cite

View full text Add to dashboard Cite

This work examines a high temperature latent heat storage system, which could find use in future concentrated solar power and other combined heat and power plants. In contrast to lab-based fully charged or totally discharged states, partial load states will be the principal operation states in real-world applications. Hence, a closer look on the partial load states and the effective power rates are worthwhile for a successful implementation of this storage type. A vertical finned shell and tube heat exchanger pipe with a combination of transversal and longitudinal fins is applied. Sodium nitrate with a melting temperature of 306 is used as phase change material and thermal oil serves as heat transfer fluid. Temperatures in the storage and the heat transfer fluid as well as the mass flow are measured for data analysis. The state of charge formulation is based on an enthalpy distribution function, where the latent heat of fusion is spread over a specific temperature range. The data show consistently high power rates for all partial load cycles at any state of charge. The mean power rate for charging is 6.78 kW with an 95.45 % confidence interval of 1.14 kW for all cycles. The discharging power rate is −5.72 kW with a 95.45 % confidence interval of 1.36 kW for all cycles. The lowest power rate is measured for the full cycle at the end of charging/discharging. It is caused by a narrow volume, which is not penetrated by fins, near the perimeter of the cylindrical heat exchanger. The state of charge formulation correlates with the storage capacity and enables state of charge based cycling. With the energy balance of the storage, the data validity is proven and further storage parameters are determined. The energy density is as high as 110 kW h m −3 and a power rate of 2.28 kW m −1 for the finned tube is confirmed. These values are highly promising for further development and application of latent heat storage systems.

show abstract

Section: Introductionmentioning

confidence: 99%

Partial cycle operation of latent heat storage with finned tubes

et al. 2020

Self Cite

View full text Add to dashboard Cite

show abstract

“…Different fin positions are focused on in [26] or [27], and fins versus pins are investigated in [28]. The influence of the fin design is shown in [29,30]. Three main findings can be summarized from the mentioned literature.…”

Section: Introductionmentioning

confidence: 99%

Heat Transfer in Latent High-Temperature Thermal Energy Storage Systems—Experimental Investigation

2019

Self Cite

View full text Add to dashboard Cite

Thermal energy storage systems with phase-change materials promise a high energy density for applications where heat is to be stored in a narrow temperature range. The advantage of higher capacities comes along with some challenges in terms of behavior prediction. The heat transfer into such a storage is highly transient and depends on the phase state, which is either liquid or solid in the present investigation. The aim is to quantify the heat transfer into the storage and to compare two different fin geometries. The novel geometry is supposed to accelerate the melting process. For this purpose, a single tube test rig was designed, built, and equipped with aluminum fins. The phase-change material temperature as well as the heat-transfer fluid temperature at the inlet and outlet were measured for charging and discharging cycles. Sodium nitrate is used as phase-change material, and the storage is operated ±30 ∘ C around the melting point of sodium nitrate, which is 306 ∘ C . An enthalpy function for sodium nitrate is proposed and the methodology for determining the apparent heat-transfer rate is provided. The phase-change material temperature trends are shown and analyzed; different melting in radial and axial directions and in the individual geometry sections occurs. With the enthalpy function for sodium nitrate, the energy balance is determined over the melting range. Values for the apparent heat-transfer coefficient are derived, which allow capacity and power estimations for industrial-scale latent heat thermal energy systems.

show abstract

Comparison of Different Heat Exchanger Tube Designs used in Latent Heat Thermal Energy Storage Systems - a Numerical Study

Cited by 2 publications

References 5 publications

Partial cycle operation of latent heat storage with finned tubes

Partial cycle operation of latent heat storage with finned tubes

Heat Transfer in Latent High-Temperature Thermal Energy Storage Systems—Experimental Investigation

Contact Info

Product

Resources

About