Correlation of electrical and swelling properties with nano free-volume structure of conductive silicone rubber composites

Abstract

The present study focuses on finding a correlation between the positron annihilation parameters of silicone rubber polydimethylsiloxane (PDMS) composites loaded with different conductive fillers and their swelling and electrical properties. Four types of conductive fillers have been used in this study, i.e., carbon black (CB), graphite (G), copper, and nickel powders. The investigated swelling parameters for PDMS composites such as the maximum degree of swelling Qm%, the penetration rate, P, and consequently the diffusion coefficient, D, decreased with increasing the filler content due to the reduction of the size of free‐volume, which could be observed through a decrease of the probability of ortho‐positronium (o‐Ps) formation I3, that has been measured by the positron annihilation spectroscopy (PALS). Accordingly, a positive correlation has been found of 76.78% and 61.1% between Qm% and the o‐Ps lifetime τ3, representing the size of free‐volume for the CB and G filled composites, respectively. It is worthwhile, mentioning that the CB filled composites exhibit relatively low values of P, D, and Qm% as compared to the G filled composites due to the difference in the physical properties of the filler, particle size, surface area as well as the tendency of the filler particles to make aggregates. On the other hand, the variation of the diffusion coefficient with the relative fractional free‐volume Fr is found in good agreement with the Fujita's free‐volume theory. On the other hand, the electrical conductivity increases with increasing the conductive filler content. Positive temperature coefficient of conductivity (PTCC) behavior is detected, except for the composite containing 20 or 25 phr CB, which showed a metallic behavior. Besides, CB filled PDMS composites exhibit higher electrical conductivity as compared to the composites filled with the other three fillers. The electrical conductivity ln (σ) is positively correlated with the probability of free annihilation of positrons at interfaces I2, thus suggesting an increase in the electron density with the filler content. The activation energy of conduction, Ea, decreases with the increase in the loading of conductive filler. Moreover, it was noticed that Ea varies with the filler type, the values of Ea increase as the particle size of the filler increases. Finally, a correlation between the free‐volume Vf, determined by PALS with the DC electrical conductivity ln(σ) is found to be in accordance with Miyamoto and Shibayma model. POLYM. COMPOS., 34:2105–2115, 2013. © 2013 Society of Plastics Engineers

Synthesis and investigation of the electrical and dielectric properties of Co3O4/(CMC+PVA) nanocomposite films

“…The maximum conductivity values, σ dc (max) , are 0.65×10 −5 , 0.83×10 −5 , 0.99×10 −5 , and 2.04×10 −5 (Ω.m) −1 for un-doped CMC/PVA, 0.3, 0.6, and 0.9 wt.% Co 3 O 4 doped CMC/PVA films, respectively. The increase of σ dc with increasing the Co 3 O 4 content could be attributed to formation of connected networks [43,44] by the physical contacts of the Co 3 O 4 NPs in the polymer matrix. In low Co 3 O 4 content such networks may not be continuous.…”

Water-Soluble Cellulose Derivatives as Suitable Matrices for Multifunctional Materials

“…MC and HPC are basically insulating materials with σ values of 8.15 × 10 −10 and 3.73 × 10 −11 S cm −1 , whereas NaCMC shows a conductivity of 4.43 × 10 −6 S cm −1 . A general conductivity increase is observed upon CoFe 2 O 4 addition due to increased interfacial effects 72.…”

Aging Mechanisms and Non-Destructive Aging Indicators of XLPE/CSPE Unshielded LV Nuclear Power Cables Subjected to Simultaneous Radiation-Mechanical Aging

“…Compared to the tensile stress, the compressive stress decreases the distance between the molecular chains; thus, more attraction bonds are generated. Besides, the compression stress reduces the free volume due to the compression of the micro-cavities that may arise under the tensile stress [ 17 , 36 , 37 , 38 ].…”