Corrosion and Tribocorrosion Behaviors for TA3 in Ringer’s Solution after Implantation of Nb Ions

Xue, Chenfei; Zhang, Pingze; Wei, Dongbo; Hu, Hengmei; Li, Fengkun; Yang, Kai

doi:10.3390/app10238329

Cited by 10 publications

(1 citation statement)

References 28 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Furthermore, Nb ion implantation forms compounds on the surface, which may contribute to improved corrosion resistance. These coatings hold promise as corrosion-resistant materials [23][24][25]. For instance, Zr and oxygen ion implantation on magnesium alloys results in ZrO 2 -containing films, reducing the corrosion rate of the treated substrates, as indicated by electrochemical and weight loss tests [26].…”

Section: Introductionmentioning

confidence: 99%

The Surface Modification of ZrO2 Film by Zr/Nb Ion Implantation and First-Principles Calculation

Gao,

Wang,

2023

Coatings

View full text Add to dashboard Cite

Zirconium dioxide (ZrO2) possesses numerous advantages such as high mechanical strength, a low friction coefficient, excellent optical properties, and an extended lifespan. Consequently, ZrO2 has a broad research foundation and practical significance in functional films and wear-resistant coatings. However, it suffers from brittleness and low ductility when used as a bio-coating material. In this study, a ZrO2 film was fabricated on Si (100) and titanium alloy substrates using a magnetron sputtering system. Subsequently, Zr and Nb ions were implanted into the film at varying doses, but with consistent energy levels. The analysis focused on the film’s microstructure, mechanical properties, hydrophilicity, and corrosion resistance. The results demonstrate a significant improvement in the hydrophilicity and corrosion resistance of the ZrO2 film following the implantation of Zr and Nb ions. First-principles calculations based on density functional theory (DFT) principles indicated that, with increasing doping concentrations of Zr and Nb in the ZrO2 model, the stability of the model increased gradually, thereby enhancing its corrosion resistance. The developed product has propelled rapid advancements in fields such as biomedical implants.

show abstract

Section: Introductionmentioning

confidence: 99%

The Surface Modification of ZrO2 Film by Zr/Nb Ion Implantation and First-Principles Calculation

Gao,

Wang,

2023

Coatings

View full text Add to dashboard Cite

show abstract

The Effect of Annealing Temperature and Immersion Time on the Active–Passive Dissolution of Biomedical Ti70Zr20Nb7.5Ta2.5 Alloy in Ringer’s Solution

et al. 2023

View full text Add to dashboard Cite

Because of their superior biocompatibility, chemical stability, and mechanical strength, Ti and Ti -based alloys are commonly utilized in orthopaedic dentistry. In Ringer ' s solution (RS), the corrosion behavior of the Ti 70 Zr 20 Nb 7.5 Ta 2.5 (T 70 Z 20 N 7.5 T 2.5 ) alloy was examined as an alternative potential material for Ti and Ti 6 Al 4 V (T 6 A 4 V) in medical applications. The corrosion resistance was evaluated utilizing potentiodynamic polarization curves (PPCs), electrochemical impedance spectroscopy (EIS), and open circuit potential techniques (OCP), supplemented by XRD and SEM surface analysis. The T 70 Z 20 N 7.5 T 2.5 alloy has the highest resistance to corrosion since it has the most stable passive state in addition to the lowest corrosion current (I corr ) and the highest corrosion potential (E corr ) in comparison with that of T 6 A 4 V and Ti. Furthermore, it was also looked at how different annealing temperatures (600, 800, and 1000 ºC)and immersion times (one, two, and three weeks) affected the corrosion behaviour of T 70 Z 20 N 7.5 T 2.5 . In comparison to the other samples, the T 70 Z 20 N 7.5 T 2.5 alloy annealed at 800 ºC demonstrated superior resistance to corrosion (the lowest I corr and I pass ). While that annealed at 1000 ºC has the lowest resistance to corrosion (highest I corr and I pass ) as a result of the passive layer dissolution. The same results are con rmed using the OCP measurements. The passive lm is composed of an inner and outer oxide layer, according to the EIS measurements. Meanwhile, the PPCs data demonstrates that the resistance to corrosion of the alloy is higher without immersion than it is with immersion and for a shorter immersion time. These results entirely agree with those of the EIS and OCP measurements of the alloy at the same immersion times. It was found that the T 70 Z 20 N 7.5 T 2.5 system consisted of α and β phases. An X-ray structural study indicated a mixture of body centred -cubic β-Ti and hexagonal close-packed α-Ti (main phase, with a grain size of about 5.35 nm). Therefore, among all the materials evaluated in this work, the T 70 Z 20 N 7.5 T 2.5 alloy can be considered a promising material suitable for use as a biomaterial.

show abstract

Improved wear and corrosion resistance of biological compatible TiZrNb films on biomedical Ti6Al4V substrates by optimizing sputtering power

Wang

Qin

et al. 2021

Surface and Coatings Technology

View full text Add to dashboard Cite

Corrosion and Tribocorrosion Behaviors for TA3 in Ringer’s Solution after Implantation of Nb Ions

Cited by 10 publications

References 28 publications

The Surface Modification of ZrO2 Film by Zr/Nb Ion Implantation and First-Principles Calculation

The Surface Modification of ZrO2 Film by Zr/Nb Ion Implantation and First-Principles Calculation

The Effect of Annealing Temperature and Immersion Time on the Active–Passive Dissolution of Biomedical Ti70Zr20Nb7.5Ta2.5 Alloy in Ringer’s Solution

Improved wear and corrosion resistance of biological compatible TiZrNb films on biomedical Ti6Al4V substrates by optimizing sputtering power

Contact Info

Product

Resources

About