Description of fabric thickness and roughness on the basis of fabric structure parameters

Sirková, Brigita Kolčavová

doi:10.2478/v10304-012-0008-6

Cited by 16 publications

(8 citation statements)

References 3 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Similar results can be observed when the fabrics are subjected to high pressure at T m . This affirms the findings of Sirkova 25 that the thickness of the fabric is dependent on the weave structure along with long floats and the yarn parameters.…”

Section: Low Mechanical Stresssupporting

confidence: 91%

“…At pressure T o , Fabrics A-3 and B-3 are the thickest, which might be attributed to the fabric structure, that is, floats in the diamond weave structure. Similar results can be observed when the fabrics are subjected to high pressure at T m. This affirms the findings of Sirkova 25 that the thickness of the fabric is dependent on the weave structure along with long floats and the yarn parameters.…”

Section: Compression Propertiessupporting

confidence: 91%

See 1 more Smart Citation

Analysis of performance properties of retro-reflective woven fabrics made with retro-reflective yarns and natural yarns

Seidu,

Jiang

2023

Textile Research Journal

View full text Add to dashboard Cite

Retro-reflective (RR) materials have been the subject of recent interest largely due to their ability to ensure personal safety on the road. Their use limits vehicle–pedestrian collisions, especially at night-time. Studies have mainly developed RR textiles for aesthetics and reported on their appearance performance accordingly. This study, however, investigates the mechanical and functional properties of RR fabrics produced with RR yarns and natural yarns. The results reveal that the woven fabrics have radiative cooling effects to transmit body heat to the environment, and a good ultraviolet protection rating (15–35) with a transmittance rate below 6% depending on the weave structure. The contact angle measurements reveal that the surface of these fabrics is hydrophobic or has low wettability. The total hand value for the fabric shows their suitability for men’s dress shirts in the winter or thin women’s dresses.

show abstract

Section: Low Mechanical Stresssupporting

confidence: 91%

Section: Compression Propertiessupporting

confidence: 91%

Analysis of performance properties of retro-reflective woven fabrics made with retro-reflective yarns and natural yarns

Seidu,

Jiang

2023

Textile Research Journal

View full text Add to dashboard Cite

show abstract

“…The average value was calculated after measuring each sample five times in different positions. 14 The areal density of the fabric samples, also expressed in grams per square meter, was measured following the ISO 3801 standard. 15 This included measuring the length, width, and weight of the fabric samples.…”

Section: Methodsmentioning

confidence: 99%

Evaluation of the wearing comfort properties for winter used electromagnetic interference shielding sandwich materials

Wang

Dana

et al. 2023

Journal of Industrial Textiles

View full text Add to dashboard Cite

This paper investigates the electromagnetic interference shielding effect and wearing comfort properties of a sandwich material consisting of a surface layer, an electromagnetic interference shielding layer, a thermal insulation layer, and a lining layer. The main aim is to research its potential as a winter jacket’s material for shielding electromagnetic radiation and the relationship between single-layer fabric samples and multi-layer sandwich materials under different properties. Experimentally, it is found that the electromagnetic interference shielding effectiveness of the sandwich materials is only determined by the electromagnetic interference shielding layer fabric sample, the other layers’ fabric samples have no significant impact on the electromagnetic interference shielding effect. In this paper, the air permeability of the sandwich materials is 25 to 50% lower than that of the single-layer fabric samples with the lowest air permeability in their combination. And the water vapor resistance of the sandwich materials is 40 to 60% higher than that of the single-layer fabric samples with the highest water vapor resistance in their combination. The thermal resistances of the sandwich materials measured by the Alambeta are lower than those calculated by the sum of the individual layers’ thermal resistance, which may be caused by the reduction in the internal air of the sandwich materials. Finally, the quality index evaluation is used to select the most suitable sandwich material for the winter jacket against electromagnetic radiation, which achieves the purpose of balancing the electromagnetic interference shielding effect and wearing comfort.

show abstract

“…44 The thickness is defined as the vertical distance between the front and back of the fabric under a given pressure. 45 The fabric thickness meter with a presser foot diameter of 50 mm was measured in this paper, and the pressure applied to the fabric was 1.0 kPa. The area density of the fabric samples was determined using ISO 3801 standards, which included the length, width, and weight of the fabric samples.…”

Section: Methodsmentioning

confidence: 99%

Enhanced electromagnetic shielding of lightweight copper-coated nonwoven laminate with carbon filament reinforcement

Hu,

Wang,

Venkataraman

et al. 2023

Journal of Engineered Fibers and Fabrics

View full text Add to dashboard Cite

Textile-based electromagnetic interference (EMI) shielding materials with good flexibility and high EMI shielding effectiveness (SE) are highly desirable. Still, the poor mechanical properties of textile-based EMI shielding materials limit their application. The carbon filaments (CF) combine superior mechanical properties and conductivity. Therefore, we demonstrate the CF-reinforced material, which was laminated with two types of copper-coated nonwoven polyester (CuPET10 and CuPET20) for EMI shielding. Compared to the traditional lamination method, this process was more convenient by ironing with adhesive lining. The developed laminate (CuPET/CF) performs superior EMI shielding property with an average SE value of 88.6 dB in the frequency range of 30 MHz to 3 GHz. The mechanical properties were improved from 12.7 to 39.9 MPa and from 13.46 MPa to 35.78 MPa for CuPET10/CF and CuPET20/CF, respectively. The newly developed material also demonstrated exceptional lightweight, flexibility, and thermal resistance. The laminated CuPET/CF material provides enhanced mechanical properties and easy lamination capability, allowing it to shield surfaces of electromagnetic radiation-sensitive equipment while providing a certain degree of protection and extremely high EMI shielding efficiency.

show abstract

Description of fabric thickness and roughness on the basis of fabric structure parameters

Cited by 16 publications

References 3 publications

Analysis of performance properties of retro-reflective woven fabrics made with retro-reflective yarns and natural yarns

Analysis of performance properties of retro-reflective woven fabrics made with retro-reflective yarns and natural yarns

Evaluation of the wearing comfort properties for winter used electromagnetic interference shielding sandwich materials

Enhanced electromagnetic shielding of lightweight copper-coated nonwoven laminate with carbon filament reinforcement

Contact Info

Product

Resources

About