Design and optimization of pi-slotted dual-band rectangular microstrip patch antenna using surface response methodology for 5G applications

Ayalew, Lijaddis Getnet; Asmare, Fanuel Melak

doi:10.1016/j.heliyon.2022.e12030

Cited by 17 publications

(7 citation statements)

References 39 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Initially, the design parameters of rectangular microstrip patch antenna are calculated using (1)-( 4) [17], after that parameters are optimized for better results. The length L and width W of the patch.…”

Section: Methods and Analysis Of Proposed Mimo Antenna 21 Design Of S...mentioning

confidence: 99%

Design and analysis of wideband four-port multiple input multiple output antenna using defective ground structure for 5G communication

Tamminaina,

Manikonda

2024

IJECE

View full text Add to dashboard Cite

This research work describes a compact four-port multiple input multiple output (MIMO) antenna using defective ground structure (DGS), and it perfectly supports the n77, n78, and n79 frequencies in 5G new radios (NR) bands. It can cover a wideband from 3.4 to 5.4 GHz with good impedance matching. The pair of antenna elements are orientated opposite to another pair with DGS. Due to this technique, it has minimal complexity, is less expensive, and improves isolation. It has also improved the frequency band's reflection coefficient and range using MIMO antenna with different stub lengths. Because it is less expensive, FR-4 substrate is used in the implementation of all antennas. Each antenna element has two identical stubs linked to the primary radiator. On the primary radiating element, a ''HI'' slot is created. The partial ground enhances impedance matching and radiation properties throughout the targeted band. The total dimensions of the four-port MIMO antenna are 46×30×1.6 mm3. The array elements' mutual coupling in the simulation is -14 dB. The ECC value is below 0.01, and the diversity gain (DG) is less than 10 dB. The suggested designs' measured gain ranges from 10 to 11.0 dB, and the radiation efficiency is nearly 91%.

show abstract

Section: Methods and Analysis Of Proposed Mimo Antenna 21 Design Of S...mentioning

confidence: 99%

Design and analysis of wideband four-port multiple input multiple output antenna using defective ground structure for 5G communication

Tamminaina,

Manikonda

2024

IJECE

View full text Add to dashboard Cite

show abstract

“…To design microstrip antennas several parameters should be taken into consideration. It is challenging to optimize this parameter [28]. One way to optimize it is to use rough set theory.…”

Section: Introductionmentioning

confidence: 99%

System design of a microstrip antenna by dimension and substrates optimization

Africa,

Pasia,

2024

Bulletin EEI

View full text Add to dashboard Cite

The microstrip antennas matured and improved over the last 25 years. Throughout these years, the limitations, and specifications of the said antennas have been overcome and significantly improved. Known to be lowprofile, suitable for mobile, and lightweight, these microstrip antennas are the focus of this research. In this paper, the researchers designed a microstrip antenna with varying lengths and substrates. They tested the changes and the effects in microstrip antennas of different lengths, along with altering substrates. To verify the differences, the researchers compared the performance parameters maximum gain (dBi), minimum gain (dBi), and S11 graph on each tested length and changed substrate. The rough set theory was used to determine the optimal design via MATLAB. From there, the researchers analyzed the results gathered and drew their respective conclusions. Additionally, they saw and compared each data result to know what antenna has the best performance parameters. From the results, a change in the dimension will result in a decrease in the said performance parameters. Furthermore, the change in substrate thickness also diminishes these changes.

show abstract

“…Because of these studies regarding the design of antennas for 5G, it is found that there is still a need to design antennas that offer good performance with sizes that allow them to be integrated into 5G devices such as the cell phone. In this study, we tried to address this problem [17]. Design and optimization of a rectangular dual-band microstrip slot-pi antenna using surface response methodology for 5G applications.…”

Section: Introductionmentioning

confidence: 99%

New microstrip patch antenna array design at 28 GHz millimeter-wave for fifth-generation application

Didi

Halkhams²,

Es-Saqy

et al. 2023

IJECE

View full text Add to dashboard Cite

This paper presents a study and an array design consisting of two microstrip patch antennas connected in series in a 2×1 form. This antenna provides better performance for the fifth-generation (5G) wireless communication system. The microstrip line feeding technique realizes the design of this antenna. This feed offers the best bandwidth, is easy to model, and has low spurious radiation. The distance between the feed line and the patch can adapt to the antenna’s impedance. In addition, the antenna array proposed in this paper is designed and simulated using the high frequency structure simulator (HFSS) simulation software at the operating frequency of 28 GHz for the 5G band. The support material used is Rogers RT/duroid® 5880, with relative permittivity of 2.2, a thickness of h=0.5 mm, and a loss tangent of 0.0009. The simulation results obtained in this research paper are as: reflection coefficient: -35.91 dB, standing wave ratio (SWR): 1.032, bandwidth: 1.43 GHz, gain: 9.42 dB, directivity: 9.47 dB, radiated power: 29.94 dBm, accepted the power: 29.99 dBm, radiation efficiency: 29.95, efficiency: 99.83%. This proposed antenna array has achieved better performance than other antenna arrays recently published in scientific journals regarding bandwidth, beam gain, reflection coefficient, SWR, radiated power, accepted power, and efficiency. Therefore, this antenna array will likely become an important competitor for many uses within the 5G wireless applications.

show abstract

Design and optimization of pi-slotted dual-band rectangular microstrip patch antenna using surface response methodology for 5G applications

Cited by 17 publications

References 39 publications

Design and analysis of wideband four-port multiple input multiple output antenna using defective ground structure for 5G communication

Design and analysis of wideband four-port multiple input multiple output antenna using defective ground structure for 5G communication

System design of a microstrip antenna by dimension and substrates optimization

New microstrip patch antenna array design at 28 GHz millimeter-wave for fifth-generation application

Contact Info

Product

Resources

About