Effect of Copper TSV Annealing on Via Protrusion for TSV Wafer Fabrication

Heryanto, A.; Putra, Wahyuaji Narottama; Trigg, A. D.; Gao, Shan; Kwon, Woocheol; Che, F.X.; Ang, X. F.; Wei, Jun; Made, Riko I; Gan, Chee Lip; Pey, K. L.

doi:10.1007/s11664-012-2117-3

Cited by 146 publications

(50 citation statements)

References 12 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The high CTE of the filled copper (i.e., 17 × 10 14,15,18 led to copper protrusion on the TSV due to copper atom movement. On the basis of mass balance, several copper cracks and voids (i.e., copper vacancies) remained in the TSV because the copper atoms thermally moved and got out the TSV, [18][19][20][21][22] as confirmed in Fig. 2e.…”

Section: Resultsmentioning

confidence: 72%

“…18,19 The copper protrusion on the TSV caused respectively by thermal expansion and diffusion of copper lattices and atoms may destroy stacked IC chips. [20][21][22] Copper must be replaced by tungsten 23 or nickel 24,25 to overcome the issue of CTE mismatch.Although the CTE of tungsten is very low, 14,26 it cannot be electrochemically plated in an aqueous electrolyte. Fortunately, tungsten can be induced to co-deposit with nickel.…”

mentioning

confidence: 99%

See 1 more Smart Citation

Microvia Filling with Nickel-Tungsten Alloy to Decrease the Coefficient of Thermal Expansion of Electronic Circuit Interconnections

Lin

Huang

Wang

et al. 2015

ECS Electrochemistry Letters

View full text Add to dashboard Cite

A nickel-tungsten alloy plating formula was developed to electrochemically fill the microvias of printed circuit boards and the through-silicon vias (TSVs) of wafers. The plating solution was composed of Ni(SO 3 NH 2 ) 2 , citric acid, sodium citrate, Na 2 WO 4 , chloride ions, and 2-mercapto-5-benzimidazolesulfonic acid. A void-free Ni-W superfilling of a microvia and a TSV were achieved. The tungsten content in the filled alloy varied from 1.5 atom% to 5.5 atom%, depending on the plating temperature. The coefficient of thermal expansion of the filled Ni-W was theoretically calculated according the tungsten content, which was lower than that of copper. Microvia filling by copper electroplating has been widely employed to fabricate state-of-the-art printed circuit boards (PCBs) for interconnection, especially for integrated circuit (IC) packaging substrates.1-5 Recently, through-silicon vias (TSVs) have also been metallized by copper electroplating for the interconnection of threedimensional (3D) IC chip stacking packaging. [6][7][8][9][10][11][12][13] Copper is a good conductor but its coefficient of thermal expansion (CTE) is high. Therefore, issues related to CTE mismatch between the conducting materials and the dielectric materials arise in PCB and 3D packaging with high-density interconnections.Numerous authors have reported that the high CTE of the copper filled in the TSVs results in stress impacts on silicon substrates. [14][15][16][17] Copper atoms diffuse from the TSV due to thermal cycling, leading to void formation in the TSV. 18,19 The copper protrusion on the TSV caused respectively by thermal expansion and diffusion of copper lattices and atoms may destroy stacked IC chips. [20][21][22] Copper must be replaced by tungsten 23 or nickel 24,25 to overcome the issue of CTE mismatch.Although the CTE of tungsten is very low, 14,26 it cannot be electrochemically plated in an aqueous electrolyte. Fortunately, tungsten can be induced to co-deposit with nickel. [27][28][29][30][31][32] In this work, a Ni-W alloy plating formula that can achieve Ni-W bottom-up filling of microvia was developed. This plating formula can fill the microvia of PCBs and can also fill TSVs. The Ni-W filled TSVs exhibit good thermal stability after being annealed at 500• C for 4 h. ExperimentalThe dimensions of the PCB fragments cut for the Ni-W filling plating were 4.2 × 6.0 cm 2 . The microvias were formed by CO 2 laser ablation. The diameter and depth of the microvias were 80 μm and 40 μm, respectively. The sidewalls of the microvias were metallized by electroless copper plating in advance to deposit a 2-3 μm thick layer of copper before the filling plating.TSVs were formed by a deep reactive ion etching (DRIE) process (i.e., the Bosch process). The thickness of the isolation layer (i.e., SiO 2 ) in the TSVs formed by thermal oxidation was approximately 1-3 × 10 3 Å. The barrier layer was a TiN film with a thickness of 500 Å, which was conformably deposited by atomic layer deposition (ALD) for 600 cycles. The seed layer was depo...

show abstract

Section: Resultsmentioning

confidence: 72%

mentioning

confidence: 99%

Microvia Filling with Nickel-Tungsten Alloy to Decrease the Coefficient of Thermal Expansion of Electronic Circuit Interconnections

Lin

Huang

Wang

et al. 2015

ECS Electrochemistry Letters

View full text Add to dashboard Cite

show abstract

“…7,8) It has been determined that Cu protrusion is not fully-reversible and that localized plastic deformation plays an important role in TSV protrusion. 9) Optimization of the annealing conditions is known to be an important factor to avoid further plastic deformation of copper in the vias. 9) Secondly, Cu-filling of the vias normally takes a long time (³approximately 15 h), and defects are most likely to occur at longer filling times.…”

Section: Introductionmentioning

confidence: 99%

“…9) Optimization of the annealing conditions is known to be an important factor to avoid further plastic deformation of copper in the vias. 9) Secondly, Cu-filling of the vias normally takes a long time (³approximately 15 h), and defects are most likely to occur at longer filling times. 10) These long processing times represent a huge drawback for the commercial realization of TSV technologies.…”

Section: Introductionmentioning

confidence: 99%

Lower Protrusion of a Copper-Nickel Alloy in a Through-Silicon via and Its Numerical Simulation

et al. 2015

View full text Add to dashboard Cite

The application of Cu-filled through-silicon via (TSV) in 3-D integrated circuit packaging faces several fabrication and reliability issues. In this study, we introduced a Cu-Ni alloy for TSV filling with a high filling speed and a reduced TSV protrusion. In particular, the characteristics of Cu-Ni via protrusions at various annealing temperatures (³200450°C) were investigated with experimental and numerical analysis and compared with Cu-filled vias. High speed Cu-Ni alloy filling into the vias was achieved without any defects by an electroplating process that used a periodic pulse reverse current waveform. The Cu-Ni alloy TSV showed lower via protrusion than the Cu TSV. The simulated protrusion heights of the Cu-Ni vias were in good agreement with the experimental results. The simulation results also indicated that the Cu-Ni TSVs has smaller protrusions than the Cu TSVs. As the annealing temperature was varied from 200 to 450°C, the protrusions increased gradually and became significant at an annealing temperature of 350°C. When the temperature was increased further, the protrusions became larger due to severe creep deformation. The von Mises stress also increased with increasing annealing temperature, and increased substantially at a temperature of 300°C due to the creep effect. In summary, the Cu-Ni alloy TSVs showed smaller protrusions relative to the Cu TSVs. The stress level of the Cu-Ni via was lower than that of the Cu via. These results indicate that the Cu-Ni alloy TSV had advantages in terms of high speed filling and smaller protrusions, demonstrating its promise as an alternative to current Cu TSV technologies.

show abstract

“…Copper pumping, which can occur in various conditions, may also affect the back-end-of-line (BEOL) structures. To investigate the mechanism of copper pumping and reduce the associated failure risk on TSVs and neighboring structures, numerical analysis [4], [7]- [11] and various experimental techniques have been utilized, including scanning electron microscopy [12]- [14], atomic force microscopy [10], [11], [14], [15], surface profilometry [9], [10], [13], [15], [16], electron backscattered diffraction [7], [8], [10], and synchrotron X-ray microdiffraction (mXRD) [17]- [19]. Compared with other experimental techniques, synchrotron mXRD, which can penetrate a several hundred micrometer thick silicon, is able to do in situ strain measurements without cross section and thus no change to the mechanical boundary conditions of TSVs.…”

mentioning

confidence: 99%

Experimental Stress Characterization and Numerical Simulation for Copper Pumping Analysis of Through-Silicon Vias

Liu

Thadesar

Taylor

et al. 2016

IEEE Trans. Compon., Packag. Manufact. Technol.

View full text Add to dashboard Cite

Abstract-In this paper, a 3-D thermomechanical model of through-silicon vias (TSVs) has been analyzed and verified with in situ microscale strain measurements by synchrotron X-ray microdiffraction. Thereafter, a comprehensive stress/strain analysis on copper pumping and back-end-of-line (BEOL) cracking issues has been carried out. In addition, a design-of-experimentsbased approach has been used to understand the effect of various parameters on copper pumping and BEOL stress. The results show that the smaller TSV diameter and thinner silicon die help reduce the copper pumping and thus mitigate BEOL stress.Index Terms-Copper pumping, finite-element analysis, synchrotron X-ray diffraction, through-silicon vias (TSVs).

show abstract

Effect of Copper TSV Annealing on Via Protrusion for TSV Wafer Fabrication

Cited by 146 publications

References 12 publications

Microvia Filling with Nickel-Tungsten Alloy to Decrease the Coefficient of Thermal Expansion of Electronic Circuit Interconnections

Microvia Filling with Nickel-Tungsten Alloy to Decrease the Coefficient of Thermal Expansion of Electronic Circuit Interconnections

Lower Protrusion of a Copper-Nickel Alloy in a Through-Silicon via and Its Numerical Simulation

Experimental Stress Characterization and Numerical Simulation for Copper Pumping Analysis of Through-Silicon Vias

Contact Info

Product

Resources

About