Electroless Ni-P-CNT composite coating on aluminum powder

Abbasipour, Benyamin; Monirvaghefi, S. M.; Niroumand, Behzad

doi:10.1007/s12540-012-6014-3

Cited by 12 publications

(3 citation statements)

References 19 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…To remedy this, CFs have been coated with metals including Cu, Ag, Co, Cr, Fe, Ti and Ni [32,[37][38][39] by physical vapor deposition (PVD), chemical vapor deposition (CVD), sol-gel, electroless plating, and electroplating [40][41][42][43][44]. Ni coating to CF is reported to lower the contact angle from 140 • to just 4 • [45] hence several methods of coating CF with Ni are noted here.…”

Section: Introductionmentioning

confidence: 99%

A Novel Nickel-Plated Carbon Fiber Insert in Aluminum Joints with Thermoplastic ABS Polymer or Stainless Steel

Nishi,

Sagawa,

Faudree

et al. 2023

Materials

View full text Add to dashboard Cite

New types of hybrid aluminum joints: Al-acrylonitrile butadiene styrene (ABS) carbon fiber reinforced thermoplastic polymer (CFRTP) designated Al/Ni-CFP/ABS, and Al-18-8 Stainless steel, Al/Ni-CFP/18-8, by Ni-plated carbon fiber plug (Ni-CFP) insert not before seen in the literature have been fabricated. The goal is to take advantage of extremely high ~6 mm CF surface area for high adhesion, to enhance the safety level of aircraft and other parts. This is without fasteners, chemical treatment, or glue. First, the CFP is plated with Ni. Second, the higher melting point half-length is spot welded to the CFP; and third, the remaining half-length is fabricated. The ultimate tensile strength (UTS) of Al/Ni-CFP/ABS was raised 15 times over that of Al/ABS. Normalized cUTS according to CFP cross-section by Rule of Mixtures for cAl/Ni-CFP/18-8 was raised over that of cAl/Ni-CFP/18-8 from 140 to 360 MPa. Resistance energy to tensile deformation, UT, was raised 12 times from Al/ABS to Al/Ni-CFP/ABS, and 6 times from Al/CFP/18-8 to Al/Ni-CFP/18-8. Spot welding allows rapid melting followed by rapid solidification for amorphous metal structures minimizing grain boundaries. The Ni-coating lowers or counters the effects of brittle Al4C3 and FexC formation at the interface and prevents damage by impingement to CFs, allowing joints to take on more of the load.

show abstract

Section: Introductionmentioning

confidence: 99%

A Novel Nickel-Plated Carbon Fiber Insert in Aluminum Joints with Thermoplastic ABS Polymer or Stainless Steel

Nishi,

Sagawa,

Faudree

et al. 2023

Materials

View full text Add to dashboard Cite

show abstract

“…Electroless plating is a facile and effective method enhancing the interfacial compatibility between fillers and metallic matrix. [24][25][26][27] In our previous investigation, we have reported that the hardness, bending strength, and tribological properties of copper-based composites are improved by the addition of copper-coated NbSe 2 and copper-coated CNTs. 7 Cui et al 3 found that because Ni-coated graphite can greatly improve the interfacial combination, the mechanical properties and wear resistance of bronze matrix are enhanced.…”

Section: Introductionmentioning

confidence: 99%

Tribological properties of Fe–Ni-based composites with Ni-coated reduced graphene oxide–MoS₂

Chen

Jia

et al. 2018

Journal of Composite Materials

View full text Add to dashboard Cite

Fe–Ni-based composites with Ni-coated reduced grapheme oxide (RGO)–MoS2 were fabricated by powder metallurgy technique, and their morphology, phase composition, and tribological properties at different temperatures were investigated systematically. Results showed that Fe–Ni-based composite with Ni-coated RGO–MoS2 possessed much more uniform and denser microstructure, and higher hardness than that with RGO–MoS2. Furthermore, Ni-coated RGO–MoS2 additive greatly allowed increasing the friction-reducing and wear-resistant properties, due to the reinforcing and lubricating effect new phase (Fe3W3C, CrxS1+x, etc.) and the improvement on interfacial compatibility between Ni-coated RGO–MoS2 and Fe–Ni matrix. In particular, as the content of Ni-coated RGO–MoS2 was 5 wt%, the friction coefficient and wear rate of the corresponding composite was decreased nearly 50% and 75%, respectively. More importantly, Ni-coated RGO–MoS2 reinforced composite kept excellent tribological properties at elevated temperature. Its friction coefficient decreased firstly with the increased temperature from 25℃ to 400℃, then increased slightly when the temperature increased to 600℃. Besides, the wear rate was only 0.73–0.9 × 10−4 mm3/Nm during the whole temperature range. This suggested that Ni-coated RGO–MoS2 was a promising additive of metallic-based composites suitable for high-temperature sliding condition.

show abstract

“…Electroless plating has been developed as one of the most convenient and effective techniques for the deposition of metal or alloy onto matrix surface [15]. More recently, some scientists have focused their intense attention on the surface treatment technique to prepare high-performance microwave absorbent owing to its advantages of simple, low-cost, controllable and readily applicable to mass production.…”

Section: Introductionmentioning

confidence: 99%

Fabrication and electromagnetic properties of novel FeNi alloy-coated flake graphite prepared by electroless plating

Liu

Gao

et al. 2016

Journal of Alloys and Compounds

View full text Add to dashboard Cite

Electroless Ni-P-CNT composite coating on aluminum powder

Cited by 12 publications

References 19 publications

A Novel Nickel-Plated Carbon Fiber Insert in Aluminum Joints with Thermoplastic ABS Polymer or Stainless Steel

A Novel Nickel-Plated Carbon Fiber Insert in Aluminum Joints with Thermoplastic ABS Polymer or Stainless Steel

Tribological properties of Fe–Ni-based composites with Ni-coated reduced graphene oxide–MoS₂

Fabrication and electromagnetic properties of novel FeNi alloy-coated flake graphite prepared by electroless plating

Contact Info

Product

Resources

About

Electroless Ni-P-CNT composite coating on aluminum powder

Cited by 12 publications

References 19 publications

A Novel Nickel-Plated Carbon Fiber Insert in Aluminum Joints with Thermoplastic ABS Polymer or Stainless Steel

A Novel Nickel-Plated Carbon Fiber Insert in Aluminum Joints with Thermoplastic ABS Polymer or Stainless Steel

Tribological properties of Fe–Ni-based composites with Ni-coated reduced graphene oxide–MoS2

Fabrication and electromagnetic properties of novel FeNi alloy-coated flake graphite prepared by electroless plating

Contact Info

Product

Resources

About

Tribological properties of Fe–Ni-based composites with Ni-coated reduced graphene oxide–MoS₂