Enzymatic Hydrolysis Combined with Mechanical Shearing and High-Pressure Homogenization for Nanoscale Cellulose Fibrils and Strong Gels

Abstract

Toward exploiting the attractive mechanical properties of cellulose I nanoelements, a novel route is demonstrated, which combines enzymatic hydrolysis and mechanical shearing. Previously, an aggressive acid hydrolysis and sonication of cellulose I containing fibers was shown to lead to a network of weakly hydrogen-bonded rodlike cellulose elements typically with a low aspect ratio. On the other hand, high mechanical shearing resulted in longer and entangled nanoscale cellulose elements leading to stronger networks and gels. Nevertheless, a widespread use of the latter concept has been hindered because of lack of feasible methods of preparation, suggesting a combination of mild hydrolysis and shearing to disintegrate cellulose I containing fibers into high aspect ratio cellulose I nanoscale elements. In this work, mild enzymatic hydrolysis has been introduced and combined with mechanical shearing and a high-pressure homogenization, leading to a controlled fibrillation down to nanoscale and a network of long and highly entangled cellulose I elements. The resulting strong aqueous gels exhibit more than 5 orders of magnitude tunable storage modulus G' upon changing the concentration. Cryotransmission electron microscopy, atomic force microscopy, and cross-polarization/magic-angle spinning (CP/MAS) 13C NMR suggest that the cellulose I structural elements obtained are dominated by two fractions, one with lateral dimension of 5-6 nm and one with lateral dimensions of about 10-20 nm. The thicker diameter regions may act as the junction zones for the networks. The resulting material will herein be referred to as MFC (microfibrillated cellulose). Dynamical rheology showed that the aqueous suspensions behaved as gels in the whole investigated concentration range 0.125-5.9% w/w, G' ranging from 1.5 Pa to 105 Pa. The maximum G' was high, about 2 orders of magnitude larger than typically observed for the corresponding nonentangled low aspect ratio cellulose I gels, and G' scales with concentration with the power of approximately three. The described preparation method of MFC allows control over the final properties that opens novel applications in materials science, for example, as reinforcement in composites and as templates for surface modification.

Flocculated flow of microfibrillated cellulose water suspensions: an imaging approach for characterisation of rheological behaviour

“…The critical concentration for gel formation is inversely proportional to fibre axial ratio a/l (diameter to length) Hill 2008;Lasseuguette et al 2008). Furthermore, the rigidity of the elastic gel network at rest (G', from a frequency sweep spectrum) above the percolation limit is scaled following the power law Pääkkö et al 2007;Hill 2008;Agoda-Tandjawa et al 2010), G 0 / ku a , where the factor k depends on axial ratio , k / ða=lÞ 2 , and exponent a on fibril volume fraction (Hill 2008), a / u.…”

Water-Resistant, Transparent Hybrid Nanopaper by Physical Cross-Linking with Chitosan

“…The mixture and NFC were shear thinning, which has also earlier been observed for pure NFC dispersions. 48 Finally, we point out that the high viscosity values shown in Figure 4b suggested us to use low concentrations to prepare the mixtures, in order to obtain homogeneous mixtures even at very high NFC-to-chitosan ratios. 49 Mechanical properties.…”

Cellulose Nanopaper Structures of High Toughness

“…The enzyme treatment can also be carried out at quite low enzyme concentration. 14 The subsequent procedure for mechanical homogenization disintegrates the cell wall into nanofibrils by subjecting dilute wood fiber suspensions to high shear forces. The homogenization method to produce mirofibrillated cellulose was originally developed by Herrick et al 15 and Turbak et al 16 Recently, we studied nanocomposites consisting of a wood cellulose nanofibril network in a plasticized potato starch matrix.…”