Fabrication of polypropylene membrane via thermally induced phase separation as a support matrix of tridodecylamine supported liquid membrane for Red 3BS dye removal

Othman, Norasikin; Harruddin, Norlisa; Idris, Ani; Ooi, Zing Yi; Fatiha, Norul; Sulaiman, Raja Norimie Raja

doi:10.1080/19443994.2015.1049554

Cited by 24 publications

(13 citation statements)

References 25 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The most important factors that influence the performance of supported liquid membrane (SLM) system are physical stability of the impregnated carrier and the rate of the mass transfer through the membrane. The structural characteristics of membrane support directly affect the performance of carrier facilitated transport membrane [ 9 ]. Many studies have focused on the search of new membrane support.…”

Section: Introductionmentioning

confidence: 99%

Application of PolyHIPE Membrane with Tricaprylmethylammonium Chloride for Cr(VI) Ion Separation: Parameters and Mechanism of Transport Relating to the Pore Structure

Chen

Hsu

2018

Membranes

View full text Add to dashboard Cite

The structural characteristics of membrane support directly affect the performance of carrier facilitated transport membrane. A highly porous PolyHIPE impregnated with Aliquat 336 is proposed for Cr(VI) separation. PolyHIPE consisting of poly(styrene-co-2-ethylhexyl acrylate) copolymer crosslinked with divinylbenzene has the pore structure characteristic of large pore spaces interconnected with small window throats. The unique pore structure provides the membrane with high flux and stability. The experimental results indicate that the effective diffusion coefficient D* of Cr(VI) through Aliquat 336/PolyHIPE membrane is as high as 1.75 × 10−11 m2 s−1. Transport study shows that the diffusion of Cr(VI) through Aliquat 336/PolyHIPE membrane can be attributed to the jumping transport mechanism. The hydraulic stability experiment shows that the membrane is quite stable, with recovery rates remaining at 95%, even after 10 consecutive cycles of operation. The separation study demonstrates the potential application of this new type of membrane for Cr(VI) recovery.

show abstract

Section: Introductionmentioning

confidence: 99%

Application of PolyHIPE Membrane with Tricaprylmethylammonium Chloride for Cr(VI) Ion Separation: Parameters and Mechanism of Transport Relating to the Pore Structure

Chen

Hsu

2018

Membranes

View full text Add to dashboard Cite

show abstract

“…In general, the membranes prepared by TIPS possess higher mechanical strength, higher porosity, and more uniform porous structures than those by NIPS . Moreover, TIPS method by far has been adopted to a series of polymers, including polyethylene, polypropylene, poly(ethylene‐ co ‐vinyl alcohol), poly(vinylidene fluoride), polyacrylonitrile, and poly(methyl methacrylate) …”

Section: Introductionmentioning

confidence: 99%

Preparation and characterization of cellulose triacetate membranes via thermally induced phase separation

Liang

et al. 2016

J of Applied Polymer Sci

View full text Add to dashboard Cite

A series of cellulose triacetate (CTA) membranes were prepared via thermally induced phase separation (TIPS) process with dimethyl sulfone (DMSO2) and polyethylene glycol (PEG400) as a crystallizable diluent and an additive, respectively. The phase separation behavior of CTA/DMSO2/PEG400 ternary system was investigated in detail by optical microscopy, differential scanning calorimetry and wide angle X-ray diffraction. This ternary system dynamically undergoes solid-solid phase separation and thus the CTA membranes possess cellular, lacy, plate-, or even ellipse-shaped pores. However, we can modulate the pore structure, porosity, water flux, and mechanical properties of the membranes by varying polymer concentration, composition of the mixed diluent, and cooling condition. Due to the intrinsic hydrophilicity, the prepared CTA membranes have better antifouling property than polysulfone membranes. These porous membranes were used as supports to fabricate thin-film composite forward osmosis (FO) membranes, which show good water permeability and selectivity.

show abstract

“…cellular, sheet-like, spherulitic, lacy, needle-like, sponge like pores). Membranes prepared via TIPS method possess higher mechanical strength, higher porosity, and more uniform porous structures than those prepared by NIPS [70,71] Various polymers such as polyethylene, polyacrylonitrile, polypropylene, poly (vinylidene fluoride), poly (methyl methacrylate) are prepared with TIPS method (Figure 8) [72,73].…”

Section: Thermally Induced Phase Separation (Tips)mentioning

confidence: 99%

A Comprehensive Review on Polymeric Nano-Composite Membranes for Water Treatment

Zahid¹,

Rashid²,

Akram³

et al. 2018

J Membr Sci Technol

188

View full text Add to dashboard Cite

During last few decades, membrane technology has emerged as an efficient technique over conventional methods due to its high removal capacity, ease in operation and cost effectiveness for wastewater treatment and production of clean water. Membrane based separations are commonly based on polymeric membranes because of their higher flexibility, easily pore forming mechanism, low cost and smaller space for installation as compared to inorganic membranes. Commonly employed membrane fabrication phase inversion method has been shortly reviewed in this article. Major limitation of membrane based separations is fouling and polymeric membranes being hydrophobic in nature are more prone to fouling. Fouling is a deposition of various colloidal particles, macromolecules (polysaccharides, proteins), salts etc. on membrane surface and within pores thus impedes membrane performance, reduces flux and results in high cost. Modification of polymeric membranes due to its tailoring ability with nanomaterials such as metal based and carbon based results in polymeric nano-composite membranes with high antifouling characteristics. Nanomaterials impart high selectivity, permeability, hydrophilicity, thermal stability, mechanical strength, and antibacterial properties to polymeric membranes via blending, coating etc. modification methods. Characterization techniques has also discussed in later section for studying morphological properties and performance of polymer nano-composite membranes. Graphical Abstract

show abstract

Fabrication of polypropylene membrane via thermally induced phase separation as a support matrix of tridodecylamine supported liquid membrane for Red 3BS dye removal

Cited by 24 publications

References 25 publications

Application of PolyHIPE Membrane with Tricaprylmethylammonium Chloride for Cr(VI) Ion Separation: Parameters and Mechanism of Transport Relating to the Pore Structure

Application of PolyHIPE Membrane with Tricaprylmethylammonium Chloride for Cr(VI) Ion Separation: Parameters and Mechanism of Transport Relating to the Pore Structure

Preparation and characterization of cellulose triacetate membranes via thermally induced phase separation

A Comprehensive Review on Polymeric Nano-Composite Membranes for Water Treatment

Contact Info

Product

Resources

About