Heat Dissipation Analysis on the Liquid Cooling System Coupled with a Flat Heat Pipe of a Lithium-Ion Battery

Mei, Nan; Xu, Xiaoming; Li, Renzheng

doi:10.1021/acsomega.0c01858

Cited by 59 publications

(25 citation statements)

References 28 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…In the actual operation and application process of the current permanent magnet synchronous motor, in order to ensure the e ectiveness and stability of the permanent magnet synchronous motor operation, it is necessary to pay more attention to and study all aspects, and the heat dissipation of the motor is a key issue that needs to be paid attention to; in the case of ideal heat dissipation of the motor, its operation can be better guaranteed. An efficient and reliable cooling system is used to quickly transfer the heat generated during the operation of the motor to the outside, which is of great significance to the life, efficiency, and operational safety of the motor [4].…”

Section: Introductionmentioning

confidence: 99%

Application of Nanofluid Electrochemistry in Heat Dissipation of Permanent Magnet Synchronous Motors

Lin

Xie

2022

Journal of Chemistry

View full text Add to dashboard Cite

In order to solve the problem of heat dissipation of permanent magnet synchronous motors, a technology using the principle of nanofluid electrochemistry is proposed. The main content of this technology is based on the characteristics and applications of nanofluids; according to the experimental system, the preparation and experimental parameters of nanofluids were determined; finally, by studying the influence of ultrasonic oscillation time and dispersant on the stability of nanofluids, it was concluded that the improvement of the thermal conductivity of nanofluids contributed to the improvement of the heat transfer rate of nanofluids. Experimental results show that when the volume fraction is 0.5, the increase rate of thermal conductivity is 1.51, the increase rate of convective heat transfer coefficient is 20.33, and the increase rate of convective heat transfer coefficient is greater than that of thermal conductivity, which shows that nanofluids have very good heat dissipation ability. It is proved that the technical research of nanofluid can meet the heat dissipation requirements of a permanent magnet synchronous motor.

show abstract

Section: Introductionmentioning

confidence: 99%

Application of Nanofluid Electrochemistry in Heat Dissipation of Permanent Magnet Synchronous Motors

Lin

Xie

2022

Journal of Chemistry

View full text Add to dashboard Cite

show abstract

“…With the improvement in the performance and cruising range of electric vehicles, the requirements for the battery management system is also growing. Therefore, a thermal management system based on phase change material or a heat pipe has also been proposed, and many papers have analyzed this thermal management method [22][23][24][25]. There are advantages and disadvantages among the various cooling systems, so the differences between these systems have also been studied and compared [26][27][28][29][30].…”

Section: Introductionmentioning

confidence: 99%

Effect of the Size and Location of Liquid Cooling System on the Performance of Square-Shaped Li-Ion Battery Modules of an Electric Vehicle

Sun

Kim

2022

Fluids

View full text Add to dashboard Cite

As the core powertrain component of electric vehicles, batteries release heat when charging and discharging due to the chemical reactions between the battery elements and internal resistance. To avoid problems resulting from abnormal temperatures, such as performance and lifespan issues, an effective battery cooling system is required. This paper presents a fundamental study of battery module liquid cooling through a three-dimensional numerical analysis. CFD numerical tests as conducted here are based on the heat transfer characteristics and on the liquid cooling theory, and the temperature distribution and thermal conductivity are analyzed qualitatively and quantitatively using Simcenter STAR CCM+ version 2016 (Siemens Digital Industries Software, Plano, TX, USA). A simulation uses a square-shell lithium-ion battery-made module with two different liquid cooling systems at different positions of the module. The results of the numerical study indicate that the bottom cooling system shows a better battery module temperature difference that is approximately 80% less than that of the side cooling system. For the side cooling system, it is better in terms of the maximum temperature of the battery module, which is approximately 20% lower than that in the bottom cooling system, but this system does not offer very good control of the temperature difference, which is also its greatest shortcoming compared to the bottom cooling system.

show abstract

“…Therefore, the high temperature among cells in a pack of battery must be controlled inside 5 degree C and the gradients of high temp in cell are ignored during the process. A BTM is used to disintegrate the heat uniformly and quickly to maintain the temperature and also to ensure the lithium ion battery process [3][4][5]. These processesare also used to maintain the battery temp inside a correct range.…”

Section: Introductionmentioning

confidence: 99%

Structural Analysis and Mechanical Properties of Thermal Battery by Flexible PCM

Pradeep¹,

Sankaramoorthy²,

Elango³

et al. 2021

JUSST

View full text Add to dashboard Cite

An ancient BTM with PCM was controlled through the issues of high inflexibility of phase change material, leakage problems and very low conductivity in thermal energy. This research paper reports a facile batter thermal management and creativity along with induced non-rigid phase change material composites. This battery model can be determined by the flexible phase change material composites along with an intervention due to the recovery in shape and non-rigidity of flexible phase change components. This assemble was modeled to be efficient and compact without any requirement for grease. A constant state reveals various stages of phase change material which has various properties in thermal efficiency. A unified state was linked with the recovery shape of flexible phase change components which can cause a low resistance in FCPCM and battery. Battery thermal management demonstrates the perfect process of thermal control power. If the battery was discharged from 90 to 10% of charge, then the temperature of flexible phase change components depends upon battery thermal management. It was 44.5°C during the 3.5°C rate which was 29.8°C lower than no phase change material. It also reveals low-temperature oscillation inside the long-time process and range of heat of recovered phase change material. The performance of battery thermal management and its flexibility will give perceptions of passive battery thermal management systems.

show abstract

Heat Dissipation Analysis on the Liquid Cooling System Coupled with a Flat Heat Pipe of a Lithium-Ion Battery

Cited by 59 publications

References 28 publications

Application of Nanofluid Electrochemistry in Heat Dissipation of Permanent Magnet Synchronous Motors

Application of Nanofluid Electrochemistry in Heat Dissipation of Permanent Magnet Synchronous Motors

Effect of the Size and Location of Liquid Cooling System on the Performance of Square-Shaped Li-Ion Battery Modules of an Electric Vehicle

Structural Analysis and Mechanical Properties of Thermal Battery by Flexible PCM

Contact Info

Product

Resources

About