Improvement of adhesion and barrier properties of biomedical stainless steel by deposition of YSZ coatings using RF magnetron sputtering

Sánchez-Hernández, Z.E.; Domínguez‐Crespo, M.A.; Torres‐Huerta, A.M.; Onofre-Bustamante, E.; Adame, J. A. Andraca; Dorantes-Rosales, Héctor J.

doi:10.1016/j.matchar.2014.02.007

Cited by 20 publications

(8 citation statements)

References 34 publications

Supporting

Mentioning

Contrasting

Unclassified

Order By: Relevance

“…For the biomedical eld, however, this is an innovative subject with great possibilities which is now under extensive research. [27][28][29] In our study, TaN lm were fabricated on Ti6Al4V substrate by magnetron sputtering. The mechanical properties were characterized by employing the X-ray diffraction (XRD), X-ray Photoelectron Spectroscopy (XPS) and nanoindenter.…”

Section: Introductionmentioning

confidence: 99%

Tantalum nitride coatings prepared by magnetron sputtering to improve the bioactivity and osteogenic activity for titanium alloy implants

Qin

Liu

et al. 2017

RSC Adv.

View full text Add to dashboard Cite

show abstract

Section: Introductionmentioning

confidence: 99%

Tantalum nitride coatings prepared by magnetron sputtering to improve the bioactivity and osteogenic activity for titanium alloy implants

Qin

Liu

et al. 2017

RSC Adv.

View full text Add to dashboard Cite

show abstract

“…All samples showed an adherence strength between 28 and 30 MPa. These values are higher than those obtained by sol-gel YSZ on carbon steel (2.5-12.4 MPa) [17], as well as YSZ deposited by RF magnetron sputtering on 316 L stainless steel (12-26 MPa) [46]. The adhesion strength was even higher than some YSZ coatings produced by plasma spray, which reported values between 15 and 30 MPa [47][48][49].…”

mentioning

confidence: 62%

Effect of Deposition Conditions on Phase Content and Mechanical Properties of Yttria-Stabilized Zirconia Thin Films Deposited by Sol-Gel/Dip-Coating

Cano

Castilleja-Escobedo

Espinoza-Pérez

et al. 2021

Journal of Nanomaterials

View full text Add to dashboard Cite

The effect of yttria concentration (0-33.4 mol%), extraction rates (0.17, 0.33, 0.50, and 0.67 mm s-1), and the number of layers (up to four) on the phase content, surface defects, thickness, hardness, adhesion strength, and wear rate of yttria-stabilized zirconia coatings produced by sol-gel/dip-coating were studied for its use on thermolabile substrates. At 700°C, a metastable tetragonal phase ( t ″ ) was obtained even with 33.4 mol% yttria when heat treated for 24 hours; however, a fully cubic structure was attained by extending the heat treatment up to 48 hours as confirmed by Raman spectroscopy. Furthermore, it was necessary to use withdrawal speeds of at least 0.67 mm s-1 to produce defect-free coatings. Although the coatings were produced at low temperature, they showed 41% lower wear rate than steel and an adhesion strength of 30 MPa. Our work stresses the importance of the heat treatment history on the stabilization of the cubic phase in sol-gel YSZ coatings.

show abstract

“…[1] to deposit YSZ and delay the corrosion of bare AISI 316L substrate is presented [2], [3], [4]. The Fig.…”

Section: Datamentioning

confidence: 99%

“…YSZ ceramic coatings were deposited on in a Tourus Kurt Lesker Coating System (1 × 10− 6 Pa) with argon chamber (20 sccm) at 50 mm (substrate-target distance) from 50 to 250 W and 30 to 120 min [1].Experimental featuresBare AISI 316 stainless steel substrate and YSZ sputtered on AISI 316L substrate were analyzed.Data source locationCICATA IPN Unidad Altamira, Tamaulipas, México.Data accessibilityMendeley Data https://doi.org/10.17632/k2njhtt479.3Related research articleZ.E. Sánchez-Hernández, M.A.…”

mentioning

confidence: 99%

Dataset of the synthesis parameters to deposit YSZ on stainless steel AISI 316L by sputtering technique

et al. 2019

Self Cite

View full text Add to dashboard Cite

The data presented in this article are related to the research previously published “improvement of adhesion and barrier properties of biomedical stainless steel by deposition of YSZ coatings using RF magnetron sputtering”. It contains the structural, morphological, compositional and electrochemical characterization of bare AISI 316L substrate which was used as a substrate to coat with yttria-stabilized zirconia (YSZ). The chemical composition and topography analyses from X-ray photoelectron spectroscopy (XPS), Auger electron spectroscopy (AES) and micrographs from atomic force microscopy (AFM) as well as the roughness value of the YSZ-sputtered coating on AISI 316L substrates are presented as complementary data of the article.

show abstract

Improvement of adhesion and barrier properties of biomedical stainless steel by deposition of YSZ coatings using RF magnetron sputtering

Cited by 20 publications

References 34 publications

Tantalum nitride coatings prepared by magnetron sputtering to improve the bioactivity and osteogenic activity for titanium alloy implants

Tantalum nitride coatings prepared by magnetron sputtering to improve the bioactivity and osteogenic activity for titanium alloy implants

Effect of Deposition Conditions on Phase Content and Mechanical Properties of Yttria-Stabilized Zirconia Thin Films Deposited by Sol-Gel/Dip-Coating

Dataset of the synthesis parameters to deposit YSZ on stainless steel AISI 316L by sputtering technique

Contact Info

Product

Resources

About